Using Sub-Addresses; Automatic Display Switch-Off - IMG STAGE LINE PARL-40DMX Bedlenungsanleitung

6.3.5 Using sub-addresses

If you use sub-addresses, you will be able to control
up to 66 spotlights (spotlight groups) independently
of each other via a single DMX start address . Thus,
the maximum number of DMX-controlled units
can be considerably higher . The spotlights with a
sub-address are selected via the DMX channel 8 . All
spotlights with a sub-address can also be controlled
in sync when the DMX channel 8 is set to a DMX
value less than 10 .
1) Adjust the spotlight for the control of 8 DMX
channels, ☞
2) Press the button MENU repeatedly until the indi-
cation on the display does not change any more .
3) Press the button  or  repeatedly until the
display shows
4) Press the button ENTER . The display now shows
and a number between 01 and 66 .
5) Adjust the sub-address with the button  or  .
6) Press the button MENU so that the display only
shows again .
7) Press the button  once so that the display
shows .
8) Press the button ENTER . The display goes to the
indication
9) If is not shown, press the button  or  as
many times as necessary .
10) Press the button ENTER . If the display shows
the sub-address function is activated . If it shows
, change to
11) For DMX control of the spotlight it is necessary
to go from the menu branch
cation of the start address:
a) Press the button MENU repeatedly until the
display shows
b) Press the button  or  repeatedly until the
display shows
c) Press the button ENTER . The display shows
the DMX start address . If now DMX control
signals are received, a dot on the display
flashes .
12) For operation of the spotlight set the DMX
channel 8 at the light controller to the DMX
value corresponding to the sub-address of the
spotlight (fig . 5) .
14
chapter 6 .3 .2 .
.
, , or .
with the button  or  .
again .
.
Sub-
address
all
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Fig. 5 Selection of spotlights with a sub-address

6.4 Automatic display switch-off

Activate the automatic display switch-off if the dis-
play is not to light up permanently but for 15 sec-
,
onds only after a button is pressed .
1) Press the button MENU repeatedly until the indi-
cation on the display does not change any more .
2) Press the button  or  repeatedly until the
to the indi-
display shows
3) Press the button ENTER . The display goes to the
indication
4) If
many times as necessary .
5) Press the button ENTER . The display shows the
present adjustment:
Select the adjustment with the button  or  .
6) Then switch back to the desired operating mode
with the operating buttons .
DMX Sub-
value address value
000 – 009
010 – 019 23
020 – 029 24
020 – 039 25
040 – 049 26
050 – 059 27
060 – 069 28
070 – 079 29
30
080 – 089
090 – 099 31
100 – 109 32
110 – 119 33
120 – 129 34
130 – 139 35
140 – 149 36
150 – 159 37
160 – 169 38
170 – 179 39
40
180 – 189
190 – 199 41
200 – 209 42
210 43
211 44
via DMX channel 8
.
, ,
is not shown, press the button  or as
: The display lights up permanently .
: The display only lights up after a button
is pressed .
DMX Sub- DMX
address value
212 45 234
213 46 235
214 47 236
215 48 237
216 49 238
50
217 239
218 51 240
219 52 241
220 53 242
221 54 243
222 55 244
223 56 245
224 57 246
225 58 247
226 59 248
60
227 249
228 61 250
229 62 251
230 63 252
231 64 253
232 65 254
233 66 255
or .