Sharp RP-15H Bedienungsanleitung Seite 6

MANUAL PLAY
4
MAINTENANCE
STYLUS CLEANING
CABINET CLEANING
If youwantto clean anypartof theunit, Wipe it With. a damp cloth
moistenedin methylated spirit (alcohol). Neveruseorganicsolvents
h suc asbenzine , thinners, or household cleaners. or serious d amage may
resu It.
DtFFERENT CARTRIDGE
1. Slidetheoutputleadconnectors ontothenewcartridge t erminals,
taking care to observe correct polarity.
Blue
Left channel
Earth
• White lead.......Left channel
SPECIFICATIONS
GENERAL
Power supply source:
AC 11ov.120V/220v.240V,
Power rating: 1Ö watts
Dimensions:
Width; 430mm
Height (including dust cover),
Depth ; 355mm
Weight
(including dust cover):
4 kg
DRIVJNG SYSTEM
Type:
Belt drive
Motor:
4-po!e synchronous
Speeds:
33-1/3 rpm and 45 rpm
Wow and flutter:
Rumble:
60 dB (DIN
Turntable:
30cm die-cast aluminium
5
Follow step1 to step4 andstep6
in the instructions for "AUTO-
MATIC PLAY" as givenon page
2. Move the cuing/pause control
lever backwards.
3. Hold the headsheii gripandswing
the tonearm to the playing posi-
tion and the turntable platter will
start to rotate.
4. Move the cuing/pause• control
'ever forward to lower the tone-
arm onto the record.
Follow step 9 to step 12 as given
5.
in the instructions for
MATIC PLAY" on page 4.
To remove lint or dust from the
stylus. follow the procedure in 'the
ill ustration. A soft brush
supplied) may be used.
Never move the brush in the lateral
direction becausethe stylus may be
damaged.
Never use.fi ngers or any objects
vvhichCoulddamagethe stylus.
MOUNTING
Red Right channel
• Green lead...... Right channel
Earth
50Hz
• 138mm
(DIN)
AUTOMATIC LEAD-INMECHANISMLAPJU$TME(WT
"AUTO-
STYLUS REPLACEMENT
Sound distortion and record damage results when a wornoutstylusis
used.Thecartridge stylussupplied hasa useful t ifeof about500hours.
(not
Good s ound reproduction requires achange toanew stylus a bout every
500 hours.Stylusassembly (part No. STY-1 17) is available from a
SHARP dealer or service centre.
TONEARM
Type:
Effective length:
CARTRIDGE
Type:
Frequency response:
Output:
Channel separation:
Tracking force:
Impedance:
Compliance:
Cartridge:
Stylus:
SHARP r eserves therightto make design a nd specification
for product improvement.
The descendingposition of the stylus
during automatic play was properly
adjusted before the unit
factory •
However, cartridge changemay have
caused a slight deviation, requiring
some adjustment.
Unplug the AC supply lead'from
1
the AC outlet.
2. If the stylus descends outside the
record edge,
cl ockwise. If the stylus descends
inside the starting groove, turn
the screw anti-clockwise.
One revolution
the descending position
10mm (3/8 in.)
How to replace:
I. Switch off the amplifier power.
2. Remove the worn out stylus as-
semblv from body of cartridge,
as indicated by the arrow
illustration.
3. Gently slide a new stylus assem-
bly into the body of cartridge.
2.
Place the cartridge 'into the head-
shell with a distance
between the stylus tip and the
end of the headshell.
Note:
On this unit the headshell cannot
be removed from
The tracking farce will require
3.
readjustment because the cartri-
dge weights differ. (Refer to the
instructions on page 3)
Statically balanced tubular arm
213mm
Magnetic type
20Hz — 20,000Hz
3 milli volts (I kHz, 50mm/sec.)
20 dB
2 grams, (recommended)
47 kilo ohms
7 x 10 cm/dyne
CART-117
STY-117
left the
turn the screw
of the screw alters
about
in the
of SO mm
the tonearm.
changes