Sharp RP-15H Bedienungsanleitung Seite 5

OPERATION
SWITCHING SPEED SELECTOR
The SPEED selector of this unit can be changedonly Whenthe turn
tableplatter is rotating. Evenif the SPEED selectoris switchedwhen
the turntable platter is not moving,the speedWill not change.
Observethe following procedurewhen changingturntable speed
AUTOMATIC PLAY
Non•standard recorddiameters suchasrecords that arenot 30cm
(12") or 17cm (7") require manual starting,
(Manual s tartingisalsorequiredif standard records arestartedat
mid-record.) R eferto the instructionsfor ''MANUAL PLAY" on
page 5.
SPEED
45
33
1. Remove the tonearm clamp.
the tonearm over the turntable
platter.
NOTE:
1, Switch on amplifier power.
2. Switch the function selector
the ampl ifier to the
position and increase the volume
slightly.
Place a record on the turntable
3.
platter (on the mat)
To play a 45 rpm record use the
4.
adaptor supplied. Place the adap-
tor over the spindle as shown
in the illustration and then place
the record on the turntable
platter.
Set the record SIZE selector
5.
the "17" (17cm 7 in.)' or "30"
(30cm 12in.) position.
Depressed position
for 17 cm record
Released position
. for 30 cm record
Switch the SPEED
6.
Refer to "SWITCHING
SELECTOR" on this page.
Move the cuing/pause
7.
lever to the front.
Push the PLAY button and the
8.
tonearm swings to the outer edge
of the record and descends.
SPEED
33
Of
PHONO
CUT
A 30—17
to
CAUTIONS WHEN PLAYING
Do not interfere with the movement of the tonearm during its
return to the arm rest or during auto lead-in.
Do not rotate the turntable platter by hand in an anti-clockwise
2.
direction.
Do not touch the stylus with either your fingers or with any hard
3.
objects.
selector.
Never move the cuing/pause control lever backwards while the
SPEED
4.
tonearm clamp is fixed.
The tonearm will not return to its rest automatically after playing a
5.
record with less than 4mm between the innermost groove contai ning
a recorded signal and the last groove of a record. In this case,push
the CUT button.and the tonearmwill automaticallyreturn to the
tonearm rest.
control
Do not changethe SPEEDselector when the turntable is stationary.
6.
Do not changethe recordSIZE selectorwhen the tonearm is in
7
motion or just after the stylusdescends o nthe recordsurface.This
action leads to turntable
If the styluscannot descendon the startinggroove precisely, t he
8.
descendingposition of the stylus must be readjustedprecisely,
Refer to the instructions
Move the cuing/pausecontrol leverbackwardsquickly whenthe
9.
PLAY button hasbeenpushedwith no recordon the turntable. If
you don't do this, majordamage maybecaused to the stylus.
Switch the SPEED selector to the
4.
"33" (33-1/3
45
rpm) position to match the speed
record
of the
After selecting
5.
tonearm to its rest manually, or
push the CUT button.
NOTE:
Never switch the SPEED selector
when a record is being played
Adjust amplifier
9.
controls to appropriate
The cuing/pause
10.
operation interrupts
and further operation
the point of
the cuing/ pause
backwards in
tonearm.
Restart record play bv sliding the
cuing/pause
wards.
11. To discontinue
point, push the CUT button. The
tonearm will
arm rest and
will be turned
The tonearm
12.
turns to the
the turntable
at the end of record
RECORDS
trouble.
on page 5.
rpm) or "45" (45
being played.
speeds return
volume and tone
levels.
control lever
record Piay
resumes at
interruption. Move
control lever
order to lift the
control lever ft) r-
record play at any
return to the tone-
turntable power
off automatically.
automatically re-
tonearm rest and
power is turned off
play.
4