Descaling; Storage; Troubleshooting; Possible Cause - Beem Coffee-Profession Gebrauchsanleitung

EN

Descaling

Limescale deposits have an adverse effect not only on the quality of the coffee and the water,
but they also cause power losses and shorten the lifespan of the device. The thicker a limescale
layer is, the more difficult it is to remove.
The automatic descaling reminder indicates when the device needs descaling. We recommend
descaling also the brewing unit with every descaling process.
For descaling we recommend the BEEM Premium Descaler Concentrate. The efficient, food-safe
and environmentally friendly BEEM Premium Descaler Concentrate is available from selected specialist
stockists, via our website www.beem.de or from our customer service department on request.
Descaling with the BEEM Premium Descaler Concentrate
1. Fill the water tank (4) up to the MAX marking with a concentrate/water solution of no
more than 1:20 (one part concentrate to 20 parts water). There should be at least 1 litre in
the water tank.
If a cleaning tablet is to be used instead of a liquid descaler, place the tablet in the powder
compartment (20).
2. Make sure that the drip tray (12) is empty and is fitted in the device correctly (see the
"Preparation" chapter).
3. Place a suitable vessel under the coffee spout (13) and, if necessary, adjust the height of the
spout to the height of the container.
4. Switch on the device by touching the touch display (19) and wait until the main menu is
displayed.
5. Touch the symbol to open the maintenance menu.
6. Touch the Descale menu item and follow the instructions on the touch display.
The device starts the descaling process.
7. Touch the symbol to open the maintenance menu again.
8. Touch the Descale brewing unit menu item and follow the instructions on the touch display.
The device starts the descaling process for the brewing unit.
9. Empty the water tank and refill it with clear water.
10. If necessary, switch the device to standby mode (see chapter ‚Operation and functions' -
‚Switching the device off').

Storage

Disconnect the device from the mains power when you are not going to use it for a prolonged
period. Clean the device again if necessary (see the "Cleaning and Care" chapter) and let it dry
completely.
Store the device and all accessories in a dry, clean, frost-free place that is protected from direct
sunlight and cannot be accessed by children or animals.
50 51

Troubleshooting

If the device does not work properly, check whether you are able to rectify the problem
yourself. If the problem cannot be solved with the steps that are listed, contact our customer
service department.
Do not attempt to repair an electrical device yourself!
Problem
The device cannot be
switched on.
The fuse in the fuse
box is triggered.
Water runs out of the
device.
Despite a pumping
noise, no water comes
out of the device.
The espresso does not
run or only runs very
slowly into the cup.
Espresso or milk has an
unpleasant taste.

Possible cause

The mains plug is not inserted Correct the fit of the mains
correctly in the plug socket. plug.
Try another plug
The plug socket is defective.
socket.
The on/off switch on the back Make sure that the on/off switch
of the appliance has not been on the back of the appliance is in
actuated. position I.
Too many devices connected to Reduce the number of devices
the same circuit. in the circuit.
There is too much water in the
Do not overfill the water tank!
water tank (4).
The drip tray (12) is full. Empty the drip tray.
There is no water in the water
Fill the water tank.
tank (4).
Take out the water tank and
The water tank is inserted
reinsert it. Make sure that it fits
incorrectly.
correctly.
The coffee spout (13) is blocked. Clean the spout.
The device is furred up. Descale the device.
Empty the bean
The coffee beans are too old. compartment (22) and add new
coffee beans.
Clean the water tank and add
The water in the water tank (4) fresh water. Do not leave water
is no longer fresh. residues standing for a long
time.
EN
Fix