Hauff-Technik FUBO RB150 Montageanleitung Seite 5

Rohrbogen mit Aufstellvorrichtung
FUBO RB
Conditions. We explicitly draw your attention to the fact that no warranty
whatsoever applies for any subsequent damage occurring as a result of failure to
follow the installation instructions or if our products are used incorrectly or
combined with third-party products.
The pipe elbow is suitable for feeding in and sealing district heating supply lines
through the base slab. The two district heating supply and return lines can be
positioned using the installation device.
Safety
This section provides an overview of all the main safety aspects for optimum
protection of personnel and a safe installation process.
If there is a failure to observe the instructions and safety information set out here,
this may result in significant hazards.
When installing the seal insert MSH PolySafe MBK, it is imperative to observe the
relevant professional association rules, the VDE provisions, the relevant national
safety and accident prevention regulations and your company's guidelines (work
and procedure instructions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to
installationof the Installation fixture FUBO RB:
WARNING!
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and property
damage.
• Observe the nationally applicable laying and filling regulations for pipes and
cables.
• Seal the underground and cable substructure well prior to laying pipes or cables
so that the latter cannot subside.
NOTICE!
No sealing due to incorrect installation!
Improper installation can result in damage.
• The incorrect laying of cables or ducts and improper filling of the cable trench
causes settlement, which can lead to damage and leaks.
• For details of other accessories and further information, see www.hauff-
technik.de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
WARNING!
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property
damage.
• Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Art. Nr.: 3030609552 Rev.: 00/2025-03-20
Skilled experts
Based on their specialist training, skills, experience and familiarity with the
relevant provisions, standards and regulations, skilled experts are able to carry out
the work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
NOTICE!
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
• When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport
damage. In the event of transport damage being visible from the outside, proceed
as follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or
delivery note provided by the transporter.
• Submit a claim for every defect as soon as it has been identified.
• Claims for damages can only be asserted within the applicable
claim period.
Scope of delivery
The scope of delivery of the pipe elbow with installation fixture FUBO RB includes:
• 1 pipe elbow with three-ribbed seal and closing cover
• 1 mounting device
Storage
NOTICE!
Damage due to improper storage!
Significant damage can occur in the event of improper storage.
• The Pipe elbow with installation fixture is to be protected from damage, damp
and soiling prior to installation. Only intact components may be installed.
• The Pipe elbow with installation fixture must be stored in such a way that it is
not exposed to low temperatures (<5 °C), high temperatures (>30 °C) or direct
sunlight.
Disposal
If no return or disposal agreement has been concluded, recycle dismantled
components after they have been properly dismantled:
• Metal remains are to be scrapped according to existing environmental
regulations.
• Dispose of elastomers according to existing environmental regulations.
• Dispose of plastics according to existing environmental regulations.
• Dispose of packaging material according to existing environmental regulations.
5