Empulse ® R90 ® Folding Axle Assemby (Folding Frames) Instruction Sheet - Sunrise Medical Empulse R90 Anleitung

Please read these instructions carefully before beginning the assembly. Failure to understand and
follow assembly instructions may result in injury to technician and/or end user and may void the
warranty. If you have any questions call Sunrise Medical Technical Support at +1(800) 333-4000.
Tools required
1. 3mm allen
wrench
2. 4mm allen
wrench
5
3
4
9
2
10
Small adapter
Medium Adapter Shown
Medium adapter
Minimum
DEALER/TECHNICIAN WARNING
Attention dealers and qualiÞ ed technicians, do not operate or service this device without Þ rst reading the owners man-
ual. If you do not understand the instructions and warnings in the owners manual please contact the Sunrise Medical
Technical Service Department before operating and/or servicing the Empulse device. Failure to do so may result in
damage and/or injury.
Find more information and important warnings in the device owner's manual or at: www.SunriseMedical.co.uk
3. 5mm allen
wrench
4. Tape measure
1
Right Hand Installation,
Small Adapter Shown
7
8
6
11
1
2
Left Hand Installation,
3
23mm
4
See page 28 for contact information
or visit www.SunriseMedical.co.uk
R90
For Folding Frame wheelchairs
Note: Folding axle adapters will be attached to camber tube but will
require adjustment to center on camber tube.
Note: Folding Frame wheelchairs always use the small 32mm clamps
without inserts.
Note: The folding axle assembly (1) will ship from the factory setup for
right hand installation. See Fig 1. To ß ip the receiver mount (10), loosen
and remove receiver mount hardware (9). Flip receiver mount so that the
bubble level (11) is on the same side as the brass bushing. See Fig 2 for
left hand installation.
A. Attaching small/medium folding axle adapters and hardware onto
wheelchairs:
1. Using 5mm allen wrench, attach Folding Axle Adapters (3) and
hardware (2) onto Axle Plates (4). Folding Axle Adapters must be
centered over the Axle Sleeve (5).
Note: The Folding Axle Adapter (3) requires the Axle Sleeve (5) to
be a minimum distance of approximately 23mm from the frame. If
the Folding Axle Adapter (3) does not Þ t as shown in Fig 3, the CG
(center of gravity) will need to be adjusted to the next available
CG position as shown in Fig. 4.
2. Tighten hardware on one side. Leave one side loose. Refer to section
C to align Folding Axle Adapter with Folding Axle. Once properly
aligned, tighten loose side.
3. Tighten hardware (2) to 9 Nm.
Note: Folding Axle Adapter (3) can be ß ipped to more easily access
the set screw. Mount the Folding Axle Adapter (3) in an orientation so
access to set screw is in the desired location.
B. Attaching folding axle to wheelchair:
1. Grab the outside of the larger tube to avoid pinching your hand
while attaching the assembly.
2. Slide the axle adapter receiver (6) over the folding axle adapter (3)
on one side.
3. Compress the folding axle assembly (1) until you are able to slide the
other axle adapter receiver (6) over the corresponding folding axle
adapter (3).
4. Check to ensure the folding axle assembly (1) is securely compressed
between the wheelchair's two axle plates (4).
FOLDING AXLE ASSEMBLY
®
(FOLDING FRAMES)
INSTRUCTION SHEET
© 2024 Sunrise Medical (US) LLC
2024-07-30 255036-EU Rev.B
ENGLISH
Page 2 of 28