elero RolMotion/D+ M Nutzungsinformation Seite 17

Assembly | Electrical connection | Adjusting the end positions
1 Press locking mechanism on the motor cable plug to-
wards the cable using a suitable screwdriver.
2 Pull out the plug.
3 Insert the motor cable plug until the lock engages.
Removing and inserting the motor cable plug
Delivery Removing plug
condition
Fig. 4 Removing and inserting the motor cable plug
5.3 Connection example for RolMotion/D+ M
230 V / 50 Hz
oder -taster
Netz
230V/50Hz
PE
N
L
Fig. 5 Connection diagram RolMotion/D+ M 230 V / 50 Hz
and cable assignment when using Hirschmann plug
connection STAS-3
Important
The motor controls in the Open and Down/Closed travel
directions must be locked against each other.
A switching time of at least 0.5 seconds must be observed.
boiter de
5.4 Parallel circuit
Important
You can connect up to 3 (maximum) RolMotion/D+ M in
de volet
parallel. Please note the maximum switching capacity of
the control unit. reseau electrique
230V/50Hz
However, the behaviour of the devices is not synchronous.
PE
N
Do not connect the RolMotion/D+ M drive in parallel with
L
other drives (e.g. elero RolTop M).
5.5 Commissioning
Important
The drive is in commissioning mode when delivered.
►The end positions may need to be adjusted using the
elero assembly cable (see Fig. 6).
►The assembly cable may only be connected to commis-
sion the drive and for adjustment operations
Inserting plug
3
1
2
M
1~
1 0 2
(3) (3)
(2) (2)
(1) (1)
M
1~
1 0 2
5.5.1 Connection for assembly cable
Fig. 6 Connection for assembly cable
►Switch on mains.
►You can now set the end positions with the elero assem-
bly cable.
5.5.2 Automatic configuration of end positions
Important
To use travel profiles, the upper and lower end positions
M
must first be set. During the "Setting the end positions" pro-
1~
cess, the blind moves in the "Standard mode" travel profile.
Automatic programming of end positions
1 Connect the electric power in accordance with
section 5.2.
2 Check for functioning: If necessary, change or swap
the assignment of the direction buttons for the operat-
ing switch/push button.
junction box
The drive switches off automatically when the upper or
lower limit stop is reached.
The teaching process is completed due to subsequent
1 0 2
travel of the shutter.
power grid
5.5.3 Changing / deleting the limit positions
230V/50Hz
PE
It is not possible to change or delete individual end posi-
N
L
tions. This is always done in pairs (upper and lower end
position simultaneously).
Changing / deleting the limit positions
1 Switch on mains
2
Use the assembly cable to bring the blind to a central
position.
M
1~
3 Press both direction keys [UP ▲]+[DOWN/CLOSE ▼]
simultaneously.
The drive travels up and down briefly after approx. 5 sec-
onds.
The end position settings have been deleted.
The end positions are configured again automatically as
described in chapter 5.5.2.
scatola di
derivatione
Changing / deleting the limit positions
Method 2 only for types RolMotion/D+ M
1 0 2
Drive in installed state: Move both direction buttons to
1
rete
the OFF position and wait 3 seconds.
230V/50Hz
2 Press the [UP ▲] button 5 times in quick succession.
PE
N
3 Press the [DOWN ▼] button 5 times in quick succes-
L
sion and hold it down the fifth time.
The drive runs up and down briefly.
The deletion of the setting of end position is completed.
The end positions can be programmed again.
Important
After deleting the end position, the travel profile default
mode is active. See also chapter 6.
© elero GmbH EN | 5