GRAPHITE 58GE130 Anleitung Seite 13

8.Lever (shield protector)
9.Battery attachment button
10.Rechargeable battery (not included)
11.LEDs
12.Special key.
* There may be differences between the drawing and the product.
EQUIPMENT AND ACCESSORIES
Shield - 1 pc.
Special spanner - 1 pc.
Additional handle - 1 pc.
PREPARATION FOR WORK
REMOVING / INSERTING THE BATTERY
• Press the battery fixing button (9) and slide out the battery (10).
• Insert the charged battery (10) into the handle holder until the
battery retaining button (9) audibly engages.
Battery types and capacities
The unit is suitable for use with ENERGY+ batteries 58G001,
58G001-1, 58G004. 58G004-1, 58G086, 58G086-1, 58GE152.
58G001
Battery type
58G001-1
Battery 2 Ah
capacity
Working time 18 min
CHARGING THE BATTERY
The device is supplied with a partially charged battery. The
battery should be charged in conditions where the ambient
0 0
temperature is 4 C - 40 C. A new battery or one that has not
been used for a long period of time will reach full power capability
after approximately 3 - 5 charge and discharge cycles.
• Remove the battery (10) from the unit.
• Plug the charger into a mains socket (230 V AC).
• When the battery pack (10) is placed in the charger, the green
LEDs (11) of the battery's state of charge are illuminated
pulsatingly in a different pattern (see description below).
Pulse lighting of all LEDs - indicates battery depletion and the
need to recharge.
Pulsating illumination of 2 LEDs - indicates partial discharge.
Pulsating 1 LED - indicates high battery charge.
When the battery is charged, all the battery charge status LEDs
(11) light up continuously. After a certain time (approx. 15s), the
battery charge status LEDs (11) go out.
The battery should not be charged for more than 8 hours.
Exceeding this time may damage the battery cells. The charger
will not switch off automatically when the battery is fully charged.
The green LED on the charger will remain lit. The battery charge
status LED will turn off after a period of time. Disconnect the
power supply before removing the battery from the charger
socket. Avoid consecutive short charges. Do not recharge
batteries after short use. A significant decrease in the time
between necessary recharges indicates that the battery is worn
out and should be replaced.
Batteries become warm during the charging process. Do not
undertake work immediately after charging - wait until the battery
has reached room temperature. This will prevent damage to the
battery.
BATTERY CHARGE STATUS INDICATION
58G004 58G086 58GE152
58G004-1 58G086-1
4 Ah 6 Ah 8 Ah
26 min 45 min 60 min
The battery is equipped with a charge status indication (3 LEDs)
(11). The lighting of all LEDs indicates a high level of charge of
the battery. The lighting of 2 LEDs indicates partial discharge.
The lighting of only 1 diode indicates that the battery is
exhausted and needs to be recharged.
INSTALLATION AND ADJUSTMENT OF THE SHIELD
The blade guard protects the operator from debris, accidental
contact with the work tool or sparks. It should always be fitted
with extra care taken to ensure that its covering part faces the
operator.
• The design of the blade guard attachment allows tool-free
adjustment of the guard to the optimum position.
• Loosen and pull back the lever (8) on the disc guard (5).
• Rotate the disc guard (5) to the desired position.
• Lock by lowering the lever(8).
• Removing and adjusting the disc guard is done in reverse order
to its installation.
TOOL REPLACEMENT
• Work gloves must be worn during tool changing operations.
• The spindle lock button (1) is only to be used to lock the spindle
of the grinder when mounting or dismounting the work tool. It
must not be used as a brake button while the disc is spinning.
Doing so may damage the grinder or injure the user.
DISC MOUNTING
• In the case of grinding or cutting discs with a thickness of less
than 3 mm, the outer flange nut (6) should be screwed on flat on
the disc side.
• Press the spindle lock button (1).
• Insert the special key (12) (supplied) into the holes of the outer
flange (6).
• Turn the key (12) - loosen and remove the outer flange (6).
• Place the disc so that it is pressed against the surface of the inner
flange (7).
• Screw on outer flange (6) and lightly tighten with special spanner
(12).
• The disassembly of the discs takes place in the reverse order to
assembly. During assembly, the disc should be pressed against
the surface of the inner flange (7) and centrally seated on its
underside.
MOUNTING OF WORKING TOOLS WITH THREADED HOLE
• Press the spindle lock button (1).
• Remove the previously mounted implement - if fitted.
• Remove both flanges - inner flange (7) and outer flange (6) -
before installation.
• Screw the threaded part of the working tool onto the spindle and
tighten slightly.
• Disassembly of threaded hole work tools is in reverse order to
assembly.
MOUNTING OF ANGLE GRINDER IN ANGLE GRINDER STAND
It is permissible to use the angle grinder in a dedicated tripod for
angle grinders, provided it is fitted correctly in accordance with the
tripod manufacturer's assembly instructions.
OPERATION / SETTINGS
Check the condition of the grinding wheel before using it. Do not use
chipped, cracked or otherwise damaged grinding wheels. A worn
wheel or brush should be replaced immediately with a new one
before use. When you have finished working, always switch off the
grinder and wait until the working tool has come to a complete
standstill. Only then can the sander be put away. Do not brake the
rotating grinding wheel by pressing it against the workpiece.
• Never overload the grinder. The weight of the power tool exerts
sufficient pressure to operate the tool effectively. Overloading
and excessive pressure can cause the power tool to break
dangerously.
13