GRAPHITE 58GE130 Anleitung Seite 12

• Do not expose the battery to fire or excessive temperatures.
Exposure to fire or temperatures above 130°C may cause an
explosion.
• NOTE: A temperature of 130°C can be specified as 265°F.
• All charging instructions must be followed, and the battery must
not be charged at a temperature outside the range specified in
the rating table in the operating instructions. Charging incorrectly
or at temperatures outside the specified range can damage the
battery and increase the risk of fire.
BATTERY REPAIR:
• Damaged batteries must not be repaired. Repairs to the
battery are only permitted by the manufacturer or an authorised
service centre.
• The used battery should be taken to a disposal centre for
this type of hazardous waste.
SAFETY INSTRUCTIONS FOR THE CHARGER
• The charger must not be exposed to moisture or water. The
ingress of water into the charger increases the risk of shock. The
charger may only be used indoors in dry rooms.
• Unplug the charger from the mains before carrying out any
maintenance or cleaning.
• Do not use the charger placed on a flammable surface (e.g.
paper, textiles) or in the vicinity of flammable substances.
Due to the temperature increase of the charger during the
charging process, there is a danger of fire.
• Check the condition of the charger, cable and plug each time
before use. If damage is found - do not use the charger. Do
not attempt to disassemble the charger. Refer all repairs to an
authorised service workshop. Improper installation of the charger
may result in a risk of electric shock or fire.
• Children and physically, emotionally or mentally challenged
persons, as well as other persons whose experience or
knowledge is insufficient to operate the charger with all safety
precautions, should not operate the charger without the
supervision of a responsible person. Otherwise there is a danger
that the device will be mishandled resulting in injury.
• When the charger is not in use, it should be disconnected
from the mains.
• All charging instructions must be followed, and the battery
must not be charged at a temperature outside the range
specified in the rating table in the operating instructions.
Charging incorrectly or at temperatures outside the specified
range can damage the battery and increase the risk of fire.
CHARGER REPAIR
• A defective charger must not be repaired. Repairs to the
charger are only permitted by the manufacturer or an authorised
service centre.
• The used charger should be taken to a disposal centre for
this type of waste.
• ATTENTION: The device is designed for indoor operation.
• Despite the use of an inherently safe design, the use of
safety measures and additional protective measures,
there is always a residual risk of injury during work.
Li-Ion batteries can leak, catch fire or explode if they are
heated to high temperatures or short-circuited. Do not store
them in the car during hot and sunny days. Do not open the
battery pack. Li-Ion batteries contain electronic safety
devices which, if damaged, can cause the battery to catch
fire or explode.
Explanation of the used pictograms
1.Read the operating instructions, observe the warnings
and safety conditions contained therein.
2.Wear safety goggles and ear protection.
3.Work in a protective mask.
4.Keep children away from the appliance.
5.Protect from rain.
6.Use indoors, protected from water and moisture.
7.Caution, sharp parts!
8.Wear protective gloves.
9.Recycling.
10.Second class of protection.
11.Selective collection.
12.Do not throw the cells into the fire.
13.Posing a risk to the aquatic environment.
14.Do not allow heat to exceed 50°C.
CONSTRUCTION AND APPLICATION
The angle grinder is a hand-held power tool powered by a battery
pack. It is driven by a permanent magnet DC commutator motor,
the speed of which is transmitted via a geared angle gear. It can
be used for both grinding and cutting. This type of power tool is
widely used for removing all types of burrs from the surface of
metal parts, surface treatment of welds, cutting through thin-
walled pipes and small metal parts, etc. With the appropriate
accessories, the angle grinder can be used not only for cutting
and grinding, but also for cleaning e.g. rust, paint coatings, etc.
Its areas of use include extensive repair and construction work
related to interior fittings, room adaptations, etc.
The appliance is intended for dry use only, not for polishing. Do
not misuse the power tool.
Misuse.
• Do not handle materials containing asbestos. Asbestos is
carcinogenic.
• Do not work with materials whose dusts are flammable or
explosive. When working with the power tool, sparks are
generated which may ignite the vapours emitted.
• Cut-off wheels must not be used for grinding work. Cut-off wheels
operate on the face and grinding with the side face of such a
wheel may damage the wheel and result in personal injury to the
operator.
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the unit shown
on the graphic pages of this manual.
1.Spindle lock button
2.Switch lock button
3.Switch
4.Additional handle
5.Shield
6.External flange
7.Inner flange
12