Start-Up And Use; Practical Advice On Using The Electric Hotplates - Indesit PIM 604 (IX) Bedienungsanleitung

V
GB
380-400V 3N~
H05RR-F 5x1.5 CEI-UNEL 35363
380-400V 2N~
H05RR-F 4x1.5 CEI-UNEL 35363
220-230V 1N~
H05RR-F 3x2.5 CEI-UNEL 35363
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indicated on the data
plate.
The appliance must be directly connected to the mains using an omnipolar
circuit-breaker with a minimum contact opening of 3 mm installed between the
appliance and the mains. The circuit-breaker must be suitable for the charge
indicated and must comply with current electrical regulations (the earthing
wire must not be interrupted by the circuit-breaker). The supply cable must
not come into contact with surfaces with temperatures higher than 50°C.
! The installer must ensure that the correct electrical connection has been
made and that it is compliant with safety regulations.
Before connecting to the power supply, make sure that:
• the appliance is earthed and the plug is compliant with the law.
• the socket can withstand the maximum power of the appliance, which is
indicated on the data plate.
• the voltage is in the range between the values indicated on the data plate.
• the socket is compatible with the plug of the appliance. If the socket is
incompatible with the plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets.
! Once the appliance has been installed, the power supply cable and the
electrical socket must be easily accessible.
! The cable must not be bent or compressed.
! The cable must be checked regularly and replaced by authorised technicians
only (see Assistance).
! The manufacturer declines any liability should these safety measures not
be observed.
! If the appliance is to be installed above a built-in electric oven, the electrical
connection of the hob and the oven must be carried out separately, both for
electrical safety purposes and to make extracting the oven easier.
16
1 2 3 4 5
1 2 4
3 5
T
S N
R
1 2 3 4 5
R
S N
4
3 5
1 2
N
R
DATA PLATE
Electrical Voltage 220-230V/380-400V 3N ~ 50/60 Hz
Max power 7000 W
connections
This appliance conforms to the following
European Economic Community directives:
- 2006/95/EC dated 12/12/06 (Low Voltage)
and subsequent amendments
- 2004/108/EC dated 15/12/04
(Electromagnetic Compatibility) and
subsequent amendments
- 93/68/EEC dated 22/07/93 and subsequent
amendments.
- 2012/19/EU and subsequent amendments.
EU Regulation no. 66/2014 implementing
Directive 2009/125/EC.
ECODESIGN
standard EN 60350-2
standard EN 50564

Start-up and use

! The position of the corresponding electric hotplate is shown on every knob.
Electric hotplates
The corresponding knob may be turned clockwise or anti-clockwise and set
to six different positions:
Setting Normal or Fast Plate
0 Off
1 Minimum power
2-5 Intermediate powers
6 Maximum power
! Please refer to the "Practical advice on using the appliance" section for a
list of the relative positions and their recommended uses.

Practical advice on using the electric hotplates

To avoid heat loss and damage to the hotplates, use pans with a flat base,
whose diameter is no less than that of the hotplate itself.
Setting Normal or Fast Plate
0 Off
1 Cooking vegetables, fish
2 Cooking patatoes (using steam) soups,
chickpeas, beans.
3 Continuing the cooking of large quantities of
food, minestrone.
4 For roasting (average)
5 For roasting (above average)
6 For browning and reaching a boil in a short time
! Before using the hotplates for the first time, you should heat them at maximum
temperature for approximately 4 minutes, without placing any pans on them.
During this initial stage, their protective coating hardens and reaches its
maximum resistance.