Rotel RP-560 Bedienungsanleitung Seite 3

Dl RECT-DRIVE SEMI-AUTOMATIC STEREO
INTRODUCTION
CAUTION
As long as the power cord is plugged into an
We at Rotel want to thank you for purchasing
AC outlet,
our audio product.
Rotel audio products are designed to use the
latest electronic technology, and they incorpo-
rate our long experience as a specialist manufac-
turer of audio equipment. We are confident
that you will find satisfaction in the high
quality sound and top performance, and that
you will find pleasure in the functional beauty
achieved through human-engineering concept.
Before starting operation, please read this
instruction manual thoroughly and acquaint
yourself with the proper mode of using the unit
and all its connections.
We hope you will enjoy top-notch performange
for many years to come.
UNPACKING
The attachments and accesSories such head
shell and counterweight are stored inside the
styrofoam moulding.
1
ACCESSORIES
TURNTABLE PLATTER
AND RUBBER MAT
POWER SUPPLY CONNECTION As the colours
of this apparatus
For power the unit requires the normal house-
the coloured
hold current (AC). You may simply plug the
terminals
unit to a wall outlet, or to your amplifier's
The wire
(or receiver's) convenience -receptacle on the
connected
rear panel. If it is plugged to a convenience
with the
receptacle marked "SWITCHED," you cannot
BLACK.
operate the unit when the power switch on the
BROWN
amplifier or receiver is set to OFF.
which is marked
ed
EXCLUSIVE NOTE FOR U.K.
If your unit comes with a 2-core cable
INSTALLATION
without a plug, make certain live and
Do not place the unit
reutral leads are connected to the proper
terminals. Check that the terminals are utilize motor or
hum. Be sure to place the unit
screøad down firmly and no loose strands
where it is free from high temperature, humidi-
of wire are present.
ty and not exposed to direct sunlight to prevent
IMPORTANT: The wires in this mains lead
possible troubles.
are coloured in accordance with the follow
Vibrations
ing code:
the performance
BLUE: NEUTRAL
LIVE the stylus skip grooves.
BROWN:
2
TURNTABLE RP-560
power is supplied to the unit.
o
of the wires in the mains lead PART NAMES
may not correspond with
(1) Head shell stand
markings identifying the
(2)
Turntableshqft
in your plug proceed as follovvs.
which is coloured BLUE must be (3)
Turntable/rubVer
to the terminal which is marked
(4)
Strobe light
letter N or coloured BLUE or
(5) EP adapter
The wire which is coloured
(6) Counterweight
must be connected to the terminal
(7)
Stylus force gauge
with the letter L or colour-
(8)
Anti-skating device
or RED.
(9)
Cueing stick
(10) Arm rest/clamp
(11) Tonearm
(12) Head shell
near appliances that
transformers to prevent (13) Stop/ reject button
in a place (14)
Speed selector
(15)
Speed control knob
and unlevel installation will affect
of the turntable and
ASSEMBLY
1. Set the main body on surface.
2. Put on the platter.
3. Lay the rubber mat.
4. Install the headshell.
5. Install the counterweight.
6.
Fix the dust cover.
CARTRIDGE INSTALLATION
If your unit is not equipped
install a cartridge onto the head shell. The lead
wires coming out of the head shell are color-
coded as below. Make sure to carry out proper
connection.
Green: Right/—
Blue: Left/—
Red: Right/+
White: Left/+
Fit the cartridge using nuts, bolts and washers,
mat
CONNECTION TO AMPLIFIER OR
RECEIVER
with a
The unit is provided with RCA cords for both
channels, and a ground wire. The RCA cord
with white plug should be connected to L (left
channel) of PHONO terminals and the
with red plug to R (right channel) of PHONO
terminals on the amplifier or receiver. Connect
the ground wire to GND terminals on the
amplifier or receiver.
GND PHONO
GND
o
o
cord
3