Cleaning The Unit; Delivery Set - Rondell Rde-1303 Die Betriebsanweisung

and smoothly and evenly lower the attachment into
the bowl (16), the grooves on the attachment (13)
should match the corresponding ledges inside the
bowl (16).
Note: Check whether the attachment (13) is set properly,
otherwise the geared lid (11) will not close.
•
Install the geared lid (11) on the chopper bowl (16).
•
Match the symbol « » on the lid (11) with the mark
on the button (17) and install the lid on the bowl (16).
Then turn the lid (11) clockwise until clicking, the mark
on the button (17) and the symbol «
must match.
•
If you have difficulty fitting the lid (11), turn the knife
(12) slightly by the drive gear so that the teeth on the
knife match the drive in the lid.
•
Install the motor unit (4) on the geared lid (11) and
slightly press on it until the locks (5) clicking.
•
Insert the power plug into the mains socket.
•
Set the required speed with the control knob (1).
•
To switch the unit on, press and hold down the but-
ton (2).
•
When the button (3) is pressed, the knife rotates at
maximum rotation speed.
•
Place the products into the chute of the lid (11), use
the pusher (21) for products feeding. Press the pusher
gently while feeding products.
•
After the use unplug the unit, press on the locks (5) and
disconnect the motor unit (4) from the lid (11).
•
Then remove the geared lid (11) from the bowl (16),
pressing the button (17) and turning the lid counter-
clockwise.
•
Carefully remove the attachment (13).
•
Take the chopped products out of the bowl (16).
•
Clean, wash and dry all the used parts immediately
after operation.

CLEANING THE UNIT

Important! Be careful when cleaning the knives (12,
18) blades, the disc (19) and the cubic grid (15).
Attention! The blades are very sharp!
•
Always switch the unit off and unplug it after operation
or before cleaning.
•
Clean, wash and dry all the used parts immediately
after operation.
•
It is recommended to wash all removable parts in warm
water with neutral detergent. You can wash the discs in
the dishwasher.
•
After processing of salty or sour products rinse the
used attachments with water immediately.
•
Clean the motor unit (4) with a damp cloth.
•
Do not use coarse sponges, abrasives and solvents to
clean the unit.
•
Do not immerse the motor unit (4), the whisk gear
(7), the potato mash making attachment gear (9), the
geared lid (11) into water or any other liquids, do not
wash them in a dishwasher.
•
For easy cleaning of the mash making attachment (10)
» on the lid (11) it is provided with removable spatulas.
•
You can remove the spatulas only if the gear (8) is
installed. Hold the attachment (10) by the gear (9) with
one hand, and with the other hand, with a little effort,
turn the removable spatulas clockwise and remove
them. Loosen the gear (9) rotating it counterclock-
wise. Wash the removable spatulas, wash the attach-
ment (10). Avoid cleaning solution getting inside the
attachment. Dry and assemble the potato mash mak-
ing attachment. Insert the attachment (10) into the gear
(9) and turn it clockwise until clicking (fixed). Install the
removable spatulas, hold the attachment (10) by the
gear (9) with one hand, and with the other hand, insert
the spatulas into the installation place and with a little
effort turn them counterclockwise until bumping.
•
While possessing products with strong dyeing prop-
erties (for instance carrot or beetroot) the bowls or
attachments can get colored, wipe the attachments or
bowls with a cloth, dampened in vegetable oil.
STORAGE
•
Clean and dry the attachments thoroughly before tak-
ing them away for storage.
•
Do not wind the power cord around the motor unit.
•
Keep the blender set away from children in a dry cool
place.

DELIVERY SET

Motor unit – 1 pcs.
Blender attachment – 1 pcs.
Whisk gear – 1 pcs.
Whisk attachment – 1 pc.
Mash making attachment gear – 1 pc.
Mash making attachment – 1 pc.
Chopper geared lid, assembled – 1pc.
Chopping knife – 1 pc.
Chopper bowl – 1 pc.
15
ENGLISH