RONDELL RDE-1303 Die Betriebsanweisung Seite 14

ENGLISH
Chopping
Warning:
– Before assembling, make sure that the power plug is
not inserted into the mains socket.
– Do not overload the processing bowl!
Attention! Be careful, the knife blades are very sharp!
•
Remove the plastic protection from the knife (18)
blades and install the knife (18) on the bowl (16) axis,
taking it by the shank.
•
Put the food into the bowl (16).
•
Install the geared lid (11) on the chopper bowl (16).
•
Match the symbol « » on the lid (11) with the mark
on the button (17) and place the lid on the bowl (16),
then turn the lid clockwise until it clicks, the mark on
the button (17) and the symbol «
must match.
•
Install the motor unit (4) on the geared lid (11) and
slightly press on it until the locks (5) clicking.
•
Insert the power plug into the mains socket.
•
Set the required speed with the control knob (1).
•
To switch the unit on, press and hold down the but-
ton (2).
•
When the button (3) is pressed, the knife rotates at
maximum rotation speed.
•
Hold the motor unit (4) with one hand and the bowl (16)
with the other hand during operation.
•
After the use unplug the unit, press on the locks (5) and
disconnect the motor unit (4) from the lid (11).
•
Then remove the geared lid (11) from the bowl (16),
pressing the button (17) and turning the lid counter-
clockwise.
•
Carefully remove the knife (18) holding it by its upper
part.
•
Take the chopped products out of the bowl (16).
•
Clean, wash and dry all the used parts immediately
after operation.
•
Put the knife (18) into the plastic protective cover.
Attention! Continuous operation time of the unit should
not exceed 20-30 seconds.
USING THE DISC (SHREDDING/SLICING)
•
Install the base (20) on the bowl (16) axis.
•
Install the disc (19) on the base (20).
Attention! Be careful, the disc blades are very sharp!
•
Install the geared lid (11) on the chopper bowl (16).
•
Match the symbol « » on the lid (11) with the mark
on the button (17) and place the lid on the bowl (16),
then turn the lid clockwise until it clicks, the mark on
the button (17) and the symbol «
must match.
•
Install the motor unit (4) on the geared lid (11) and
slightly press on it until the locks (5) clicking.
•
Insert the power plug into the mains socket.
•
Set the required speed with the control knob (1).
•
To switch the unit on, press and hold down the but-
ton (2).
•
When the button (3) is pressed, the disc rotates at max-
imal rotation speed.
•
Place the products into the chute of the lid (11), use
the pusher (21) for products feeding. Press the pusher
gently while feeding products.
•
» on the lid (11) After the use unplug the unit, press on the locks
(5) and remove the motor unit (4) from the geared
lid (11).
•
Then remove the geared lid (11) from the bowl (16),
pressing the button (17) and turning the lid counter-
clockwise.
•
Carefully remove the disc.
•
Take the chopped products out of the bowl (16).
•
Clean, wash and dry all the used parts immediately
after operation.
USING THE CUBIC ATTACHMENT
Use the cubic attachment for cutting fruit and boiled veg-
etables.
Attention! Do not process hard ingredients such as fruits
with stones, meat with bones, and frozen foods. They can
block and damage the cubic attachment.
Tip: if you want to process different ingredients without
clearing the grid (15) in between, always start with the
softest ingredients.
For instance, to make a fruit salad, start with banana,
then proceed with mango and finish with apples.
Warning: before assembling make sure that the pow-
er plug is not inserted into the socket.
•
Install the grid (15) into the cubic attachment (13).
•
Open (pull aside) the metal locks (14), place the knife
(12) on the attachment (13) and fix it with the locks (14).
Attention! Be careful, the knife blades are very sharp!
•
For the safety of further assembly, hold the
assembled attachment by the knife (12) drive gear
located in its center.
•
Match the mark on the side surface of the attach-
ment (13) with a similar mark on the button (17)
14
» on the lid (11)