Artillery Sidewinder X4 Plus Bedienungsanleitung Seite 14

3. Introduction to the Equipment Screen Interface
3.4 Leveling Setting
Perform Z-axis offset first: click "Set" → "Calibration" → "Automatic
1
leveling",Click "Z=0" and adjust the Z-axis offset after the machine
returns to zero,so that the height from the nozzle to the platform is
about the thickness of A4 paper (0.08-0.1mm), and there is
obvious friction feeling when drawing A4 paper.
Loading Loading
Moving Calibration
Moving Calibration Network
consumables consumables
0 . 1 m m 1 m m 1 0 m m
Automatic leveling
Manual leveling
zero
Unlock Resonance
compensation
0 0 0 0 0 0 0 0 0
Home page Tools Settings Print
Home page Tools Settings
Manual leveling: Return to zero printer, and click "Set" → "Calibration"
2
→ "Manual leveling" on the touch screen.
Loading Loading
Moving Calibration
Moving Calibration Network
consumables consumables
0 . 1 m m 1 m m 1 0 m m
Automatic leveling
Manual leveling
zero
Unlock Resonance
compensation
0 0 0 0 0 0 0 0 0
Home page Tools Settings Print
Home page Tools Settings
3 Place a piece of A4 paper between the heating head and the hot bed.
Network
Move up
0.01 0.05 Move up
0.01 0.05
Move down
0.1 1 Move down
0.1 1
Zoffset=0 Z=0
Zoffset=0 Z=0
Use the Move Up/Move Down key on the right to
Use the Move Up/Move Down key on the right to
adjust the height of the platform so that the leveling
paper has a slight friction between the nozzle and the adjust the height of the platform so that the leveling
paper has a slight friction between the nozzle and the platform, and then click the key below.
platform, and then click the key below.
Save Save Next step Next step
Print
Network
Print
Move the heating head to 7 points in turn through the touch screen.
4
Loading Loading
Moving Calibration
Moving Calibration Network
consumables consumables
0 . 1 m m 1 m m 1 0 m m
Automatic leveling
Manual leveling
zero Unlock Resonance
compensation
0 0 0 0 0 0 0 0 0
Home page Tools Settings Print
Home page Tools Settings
Adjust the knob at the bottom of the hot bed to ensure that the height from
5
the nozzle at seven points to the printing platform is about the thickness of
A4 paper (0.08-0.1 mm).
Finally, carry out automatic leveling: click "Set" → "Calibration" → carry out
6
the "Auto-leveling" page to adjust the Z offset. → "Next" on the touch screen
for automatic leveling, and wait for the automatic leveling program to end.
Loading Loading
Moving Calibration Network Moving Calibration Network
consumables consumables
0 . 1 m m 1 m m 1 0 m m
Automatic leveling
Manual leveling
zero
Unlock Resonance
compensation
0 0 0 0 0 0 0 0 0
Home page Tools Settings Print Home page Tools Settings Print
Manual leveling Manual leveling
Network
Point 1 Point 2
Point 1 Point 2
Point 3 Point 4
Point 3 Point 4
Point 5 Point 6
Intermediate point
Point 7
Next step
Next step
Print
Move up
0.01 0.05
Move down
0.1 1
Zoffset=0 Z=0
Collecting 121 compensation values, please
Use the Move Up/Move Down key on the right to
adjust the height of the platform so that the leveling
paper has a slight friction between the nozzle and the
platform, and then click the key below.
Save Next step
11
23
wait......