User Manual; Assembling The Machine; Machine Assembly Procedure; Commissioning - Vari Cb-80 Bersetzung Der Originalbetriebsanleitung
Inhaltsverzeichnis
Verfügbare Sprachen
Verfügbare Sprachen
2.4 User manual
2.4.1 Assembling the machine
Assembly and operating instructions are available from your retailer as a component of pre-sales service!
Given that the packaged machine is not fitted with wheels and in view of its total weight ensure that the machine is
always assembled with the assistance of another person.
Handling points when removing the machine from the box (see Fig. 1 marked
engine plate, at the back of the machine frame tube.
2.4.1.1 Machine assembly procedure
Given that the packaged machine is not fitted with wheels and in view of its total weight ensure that the machine is
always assembled with the assistance of another person.
According to Fig. 2 - remove from the box both cylinder sweeping brushes
1)
brushes
2
, the axle pin
2)
Remove the paper index
3)
Position yourself and your assistant at the longer sides of the box, grasp the machine by the front and back grip points (see
detail below on the right, Fig. 1 ) and remove it from the box in the forward direction. Prop it by the gearbox
out paper insert
the lower plastic covers
4)
Fit washers 21
6
11
. Bear in mind the direction of rotation of the wheels! The direction of rotation is shown on the side of the wheel.
5)
Fit the support weel
6)
Fit the mudguard
7)
Fit the turning lever
between the turning lever foot
and the carrier plate must be 20 mm. The rubber profiles
8)
Fit both cylinder sweeping brushes
pin
3
is inserted with the stub first from the left side of the machine. Fit washers 13
nuts
24
well.
9)
Turn the handlebars
to set their height, and one of two holes in the frame pipe). Apply lubricant grease on the thread of the bolt
bolt
26
well using the wing nut
and must pass through between the bolt
10) Remove the two ties
place under the handlebars crossbar.
2.4.2 Commissioning
The machine may be supplied without engine fluids (depending on various national regulations)!
1.
Check the oil level; if necessary, fill the engine with the recommended type and amount of oil. Fill the tank with the recommended
type and amount of gasoline.
2.
The gearbox of the drive and of the cylinder sweeping brushes is filled with oil from the factory
2.4.3 Control elements
2.4.3.1 Starting the engine
First read through the instruction for use
engine.
Positons
1
=STOP,
2
=MIN,
positions latch in their positions by means of a simple slot-and-projection system made in the lever body.
1.
On engines fitted with mechanical choke move the accelerator lever into position
choke or PRIMER move the lever to position
When starting the engine both control levers (
handlebars)!
2.
Start the engine manually by a rapid pull on the starter recoil cord
3.
Let a new or cold engine run for about 30 seconds with the choke on
move the accelerator lever to the
fitted with automatic choke wait until the engine revolutions stabilize.
Please acquaint yourself with the required oil change intervals in Chapter 2.6.2 Lubrication of the machine
57
58
The original manual and the English translation is part of the machine.
Directions for starting the engine are described in detail in the engine operating instructions.
59
60
Ungines equipped with automatic choke and throttle lever in MAX position, automatic setting of maximum rpms occurs after the engine has warmed.
3
and both wheels
4
7
beneath the handlebars and spread it on the ground in front of the box.
7
and hold the rare part of the machine at a level that does not touch the insert so that it does not deform
9
.
and both wheels
4
and
12
and secure with a split pin
14
using the screws
15
, nuts
2
using M8x35 screws
2
and the carrier plate
2
, there is no difference between the left and right sides, they are identical. The axial
25
and attach them to the pipe at the rear of the frame (choose one of the three holes in the handlebars
27
and washer 8,4
26
and the frame pipe.
29
from the bag with the instructions, see Fig. 1 and tighten the bowden cables to the handlebars in
3
=MAX and
4
=CHOKE of the accelerator lever are described in Fig. 4 . All four described main
3
=MAX.
3
MAX position. Let the engine run in this position for about 30 seconds. In case of engines
- ahead of the engine behind the square tube on the
and
5
. Remove the bag with parts.
5
onto the axle, secure each with a lock pin
13
in the highest position.
16
and flat washers
17
18
and M8 nuts
19
with 8,4 washers
21
. After tightening the bolted joints the distance between the foot
22
are slightly compressed.
28
. The bowden cables from the control levers must not be crossed
58
of the engine! You may prevent possible damage to the
1
and
2
Fig. 3 ) must be in the OFF position (not pressed to the
59
.
60
(the accelerator lever in the
CB-80 CB-80B CB-80Z CB-80ZI
1
, the turning lever of the cylinder sweeping
10
and then wiht a lock ring
.
20
. Insert the rubber profiles
23
on the pin and tighten both M10
26
57
.
4
=CHOKE. On engines fitted with automatic
4
CHOKE position), then
8
on the spread
22
and tighten the
25
Kapitel
Inhaltsverzeichnis
