Milwaukee HEAVY-DUTY AG 11-115 Originalbetriebsanleitung Seite 17

TECHNICAL DATA
Safety Warnings Specifi c for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush with
the guard. Wire wheel or brush may expand in diameter due to
work load and centrifugal forces.
Appliances used at many different locations including open air
should be connected via a residual current device of 30 mA or less.
Dust and splinters must not be removed while the machine is
running.
Only plug-in when machine is switched off.
Never reach into the danger area of the tool when it is running.
Always use the auxiliary handle.
Always use the protecting cap when roughing-down and
separating.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in
order to fi nd out the cause.
Always use and store the grinding disks according to the
manufacturer's instructions.
When grinding metal, fl ying sparks are produced. Take care that
no persons are endangered. Because of the danger of fi re, no
combustible materials should be located in the vicinity (spark fl ight
zone). Do not use dust extraction.
Due care should be taken that no sparks or sanding dust fl ying
from the workpiece come into contact with you.
When separating stone the guide shoe must be used!
The adjusting nut must be tightened before starting to work
with the machine.
The workpiece must be fi xed if it is not heavy enough to be steady.
Never lead the workpiece to the grinding disk with your hand.
Under extreme conditions (e.g. smooth-grinding metals with
the arbour and vulcanized fi bre grinding wheel), signifi cant
contamination can build up on the inside of the angle grinder.
For safety reasons, in such conditions the inside should be
cleaned thoroughly of metal deposits and a motor circuitbreaker
must be connected in series. If the motor circuitbreaker
trips the machine must be sent for repair.
For accessories intended to be fi tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to accept
the spindle length.
For cutting or separating use a closed protection cap, available
as an accessory.
SPECIFIED CONDITIONS OF USE
This angle grinder can be used for separating, grinding, sanding
and wire brushing many different materials, e.g. metal or stone.
In case of doubt please read the instructions of the accessories
manufacturer. Do not use this product in any other way as stated
for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product is in
conformity with the following standards or standardized
documents: EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-2,
EN 61000-3-3, in accordance with the regulations 98/37/EC,
2004/108/EC
Winnenden, 2009-03-09
MAINS CONNECTION
Connect only to single-phase a.c. current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the design
conforms to safety class II.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Do not let any metal parts reach the airing slots - danger of short
circuit!
Use only Milwaukee accessories and spare parts. Should
components need to be exchanged which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the ten-digit No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: Milwaukee Electric Tool, Max-Eyth-Straße 10,
D-71364 Winnenden, Germany
SYMBOLS
Please read the instructions carefully before
starting the machine.
Always wear goggles when using the machine.
Always disconnect the plug from the socket
before carrying out any work on the machine.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2002/96/EC on waste electrical
and electronic equipment and its implementation
in accordance with national law, electric tools that
have reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Rainer Kumpf
Manager Product Development
GB
English
13