Noise And Vibration Data; Environmental Protection - Graphite 58Ge118 Benutzerhandbuch

Rechargeable battery (not included)
9
PURPOSE AND CONSTRUCTION
The electric blower is a battery-operated device powered by a DC motor. The
electric blower is a dual-purpose device designed for blowing and suction
for cleaning around the house and home garden as well as the workshop.
Among other things, it is suitable for cleaning and removing leaves, grass
clippings from terraces, roads and paths. The machine is not designed for
industrial use and is intended for outdoor work.
OPERATION OF THE DEVICE
Figure A shows a schematic representation of the components*
∗
Slight differences between illustrations and actual product may occur
Before starting work, ensure that all components are operational and
the battery is charged
INSTALLATION DEPENDING ON THE OPERATING MODE
Blower mode - in this mode the working nozzle Picture A1 is installed on
the nozzle seat Picture A2 . The correct installation of the working nozzle
is illustrated in Picture B. The working nozzle Picture B1 has 2 tabs
Picture B2, which must be fitted into the grooves in the seat Picture B3.
After inserting the nozzle, push it towards the unit and then carefully turn
it clockwise until it stops. Once the battery is installed, the unit is ready for
operation.
Vacuum mode - in this mode the working nozzle fig. A1 ; fig. C1 is
installed on the seat fig. A7 ; fig. C3 the tabs fig. C2 must be inserted into
the grooves of the seat fig. C3. After inserting the nozzle, push it towards
the device and then carefully turn it clockwise until it stops.
The second step is the installation of the collecting bag (picture A6)
on the blower nozzle seat (picture A1). The plastic end of the bag has the
same grooves inside as the working nozzle. You must fit the grooves fig.
D1, which must be placed in the grooves of the seat fig. D3. After inserting
the nozzle, push it towards the appliance and then carefully turn it
clockwise until it stops. Once the battery has been installed the unit is
ready for operation.
Emptying the spoil bag - to remove the collected material, carefully
remove the bag from the machine, open it by carefully pulling the zipper.
Then dispose of the collected material in the designated area.
Starting the unit - after installing the battery (not supplied) in the socket
fig. A8, hold the unit firmly in your hand by the operating handle fig. A5
press the switch in the direction of the handle fig. E1. To switch off the
device just release the switch. The Blower has no continuous operation
button.
Speed regulation - The blower is equipped with a speed regulation. For
this purpose there is a switch (Fig. A3), depending on the pressure on the
switch the speed can be increased or decreased. The higher the pressure
the higher the speed. The device additionally has a mechanical 3 position
rev limiter fig. A4. Maximum rpm for the stop setting values are shown in
the table below.
Setting
Low speed setting (1)
Medium speed setting (2)
High speed setting (3)
Set contents:
• Blower/vacuum cleaner
• Working nozzle
• Dredge bag
Rated data
Air flow
Maximum speed
Max. motor speed at no load
Rated voltage
Protection class
Degree of protection
Overall length (without battery)
Net weight (with nozzle without
battery)
58GE118 indicates both the type and the machine designation

NOISE AND VIBRATION DATA

Sound pressure level
Sound power level
Vibration acceleration values
Value
0-6000/min
0-12000/min
0-18000/min
0-2.6m³/min
0-252 km/h
18000 min
-1
D.C. 18V
III
IPX0
487.5 mm
1,1kg
Lp = 77,5 dB(A) K= 3 dB(A)
A
Lw = 89,3 dB(A) K= 3 dB(A)
A
= 1.433 m/s K= 1.5 m/s
2 2
a
h
Information on noise and vibration
The noise level emitted by the device is described by: the level of emitted
sound pressure Lp and the sound power level Lw
A
measurement uncertainty). Vibration emitted by the device is described by
the vibration acceleration value a
uncertainty).
The sound pressure level Lp
vibration acceleration value a
measured in accordance with IEC 60335-1. The specified vibration level
can be used for comparison between devices and for preliminary
a
h
assessment of vibration exposure.
The vibration level given is representative only of the basic use of the
device. If the machine is used for other applications or with other working
tools, the vibration level may change. A higher vibration level will be
caused by insufficient or infrequent maintenance of the machine. The
reasons given above may result in an increased vibration exposure during
the entire working period.
To accurately estimate vibration exposure, it is necessary to take
into account periods when the equipment is switched off or when it
is switched on but not used for work. When all factors are accurately
estimated, the total vibration exposure may be significantly lower.
In order to protect the user from the effects of vibration, additional safety
measures should be implemented, such as: cyclical maintenance of the
machine and working tools, securing an appropriate hand temperature
and proper work organisation.

ENVIRONMENTAL PROTECTION

Electrically powered products should not be disposed of with
household waste; instead they should be taken to the appropriate
disposal facilities. Please consult your product dealer or local authority
for information on disposal. Waste electrical and electronic equipment
contains substances that are not harmful to the environment. Equipment
which is not recycled poses a potential hazard to the environment and
human health.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with
headquarters in Warsaw, ul. Pograniczna 2/4 (hereinafter: "Grupa Topex") informs that all
copyrights to the content of this manual (hereinafter: "Manual"), including among others.
Its text, photographs, diagrams, drawings, as well as its composition, belong exclusively
to Grupa Topex and are subject to legal protection under the Act of 4 February 1994 on
Copyright and Related Rights (ie Journal of Laws 2006 No. 90, item 631, as amended).
Copying, processing, publishing, modification for commercial purposes of the entire
Manual, as well as its individual components, without the consent of Grupa Topex
expressed in writing, is strictly prohibited, and may result in civil and criminal liability.
EC Declaration of conformity
Manufacturer: Grupa Topex Sp. Z o.o. Sp.k., Pograniczna Street 2/4
02-285 Warszawa
Product: Cordless blower
Model: 58GE118
Trade name: GRAPHITE
Serial number: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility of
the manufacturer.
The product described above complies with the following documents:
Machinery Directive 2006/42/EC
Electromagnetic Compatibility Directive 2014/30/EU
RoHS Directive 2011/65/EU as amended by Directive 2015/863/EU
Noise Emission Directive 2000/14/EC as amended by 2005/88/EC
Guaranteed sound power level L
Measured sound power level L
And meets the requirements of the standards:
EN 60335-1:2012/A2:2019; EN 50636-2-100:2014; EN 62233:2008; EN
ISO 12100:2010;
EN 55014-1:2017; EN 55014-2:2015;
IEC 62321-2:2013; IEC 62321-3-1:2013; IEC 62321-4:2013+A1:2017;
IEC 62321-5:2013; IEC 62321-6:2015;
IEC 62321-7-1:2015; IEC 62321-7-2:2017; IEC 62321-8:2017
This declaration relates only to the machinery as placed on the market
and does not include components
added by the end user or carried out by him/her subsequently.
Name and address of the person residing or established in the EU
authorised to prepare the technical file:
Signed on behalf of:
Grupa Topex Sp. z o.o. Sp.k.
2/4 Pograniczna Street
02-285 Warsaw
6
(where K denotes
A
(where K is the measurement
h
, the sound power level Lw
A
specified in this manual have been
h
=93 dB(A)
WA
=89,3 dB(A) K=3 dB(A)
WA
and the
A