GUDE Systems Expert Power Control 8101 Serie Anleitung Seite 69

Spezifikationen
console serial echo show
console serial kvm set {OFF=0|ON=1}
console serial kvm show
console serial utf8 set {OFF=0|ON=1}
console serial utf8 show
console serial login set {OFF=0|ON=1}
console serial login show
console serial login local set {OFF=0|ON=1}
console serial login local show
console serial login radius set {OFF=0|ON=1}
console serial login radius show
console serial login delay set {OFF=0|ON=1}
console serial login delay show
console serial pushmsgs config set {OFF=0|
ON=1}
console serial pushmsgs config show
console serial pushmsgs set {OFF=0|ON=1}
console serial pushmsgs show
console serial user set "{username}"
console serial user show
console serial passw d set "{passw d}"
console serial passw d hash set "{passw d}"
email
email enabled set {OFF=0|ON=1}
email enabled show
email sender set "{email_addr}"
email sender show
email recipient set "{email_addr}"
email recipient show
email server set "{dns_name}"
email server show
email port set {ip_port}
email port show
email security set {NONE=0|STARTTLS=1|SSL=2} sets SMTP connection security
email security show
email auth set {NONE=0|PLAIN=1|LOGIN=2}
email auth show
email user set "{username}"
email user show
email passw d set "{passw d}"
email passw d hash set "{passw d}"
email testmail
ethernet
ethernet mac show
ethernet link show
ethernet phyprefer set {10MBIT_HD=0|
10MBIT_FD=1|100MBIT_HD=2|100MBIT_FD=3}
ethernet phyprefer show
extinput
extinput {port_num} {inp_num} state show
extinput all state {MODE0=0|MODE1=1|MODE2=2}
show
extinput {port_num} {inp_num} name set "{name}" sets sensor name to label
extinput {port_num} {inp_num} name show
extinput {port_num} {inp_num} invert enabled set
{OFF=0|ON=1}
extinput {port_num} {inp_num} invert enabled
show
extinput {port_num} {inp_num} label {LOW=0|
HIGH=1} set "{name}"
extinput {port_num} {inp_num} label {LOW=0|
HIGH=1} show
69
Expert Power Control 8101
show s if echo enabled
enables binary KVM cmds on serial port on/off
show s if binary KVM cmds enabled
enables UTF8 support
show s if UTF8 enabled
enables login on/off
show s if login enabled
enables local login on/off
show s if local login enabled
enables login for RADIUS on/off
show s if RADIUS login enabled
enables delay (after 3 login fails) on/off
show s if login delay enabled
enables persistent push msgs
show s if persistent push msgs are enabled
enables temporary push msgs
show s if temporary push msgs are enabled
sets login user name
show s login user name
sets login passw ord
sets login hashed passw ord
enters cmd group "email"
enables email on/off
show s if email is enabled
sets email sender address
show s email sender address
sets email recipient address
show s email recipient address
sets email SMTP server address
show s email SMTP server address
sets email SMTP port
show s email SMTP port
show s SMTP connection security
sets email authentication
show email authentication
sets SMTP username
show s SMTP username
sets SMTP passw ord
sets crypted SMTP passw ord
send test email
enters cmd group "ethernet"
show s MAC address
show s ethernet link state
sets preferred speed for PHY Auto Negotiation
show s preferred speed for PHY Auto Negotiation
enters cmd group "extinput"
show s input state
show s input state of all ports in 3 different view
modes
show s label of sensor
inverts input on/off
show s if input inverted
sets input low /high text
show s input low /high text
4
© 2023 GUDE Systems GmbH