Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EXPLODED VIEW
SPARE PARTS LIST FEAS-1440
REF NR
DESCRIPTION
2
KEYLESS CHUCK
4
SWITCH
7
BATTERY 14.4 V, 1000 mA
-
CHARGER, 14.4 V
-
ADAPTOR , 3 - 5 hr
12
ELECTRICAL SAFETY
Replacing cables or plugs
Dispose of old cables or plugs immediately they are
replaced by new ones. Connecting a plug on a loose
cable to a socket is dangerous.
MOUNTING ACCESSORIES
Fig. B
FITTING AND REMOVING DRILL CUTTERS
In addition to drill cutters, the tool can also
accommodate screwdriver bits with a hexagonal shaft.
•
Loosen the drill chuck (4) by rotating the hand-grip
(9).
•
Insert the shaft of the drill cutter into the chuck.
•
Tighten the drill chuck so that the drill cutter is firmly
clamped.
•
Rotate the drill chuck in the opposite direction when
you wish to change the cutter.
CONNECTING AND REMOVING THE
BATTERY
Fig. C
•
Ensure that the direction reversing switch (2 Fig. A) is
in the central position in order to prevent the
appliance from being switched on unexpectedly.
•
Insert the charger (5) into the base of the appliance,
as shown on the illustration. Push the battery until it
latches in.
•
Press the locking buttons (10) on both sides before
removing the battery, and disengage the battery
from the base of the appliance.
OPERATION
FERM NR
Hold the appliance firmly and press the drill cutter
406190
steadily onto the workpiece. Do not overload the
406189
appliance.
Only use drill cutters with no visible wear. Worn drill
-
cutters will have a bad effect on the functioning of the
406178
appliance.
406179
Ferm
Ferm
Always check whether your battery voltage
matches that shown on the rating plate. Also find
out whether your mains voltage matches the input
voltage of the charger.
The battery charger is doubly insulated in
compliance with EN60335; it therefore does not
require earthing.
Always remove the battery before starting work.
Ensure that the exterior of the battery block or tool
is clean and dry before connecting the charger.
Always follow the safety notes and the relevant
safety code.
ADJUSTING THE TORQUE
Fig. D
The appliance has 16 different torque settings with
which to set the power for driving and removing screws.
•
Set the torque adjustment ring (3) to the desired
position.
The available torque settings are indicated on the
adjustment ring by the numbers 1 to 8 and by dots
between the figures to define intermediate settings
(16 in total).
•
You should preferably choose as low a setting as
possible when using the screwdriver. Select a higher
setting if the motor slips.
DRIVING AND REMOVING SCREWS
•
Set the direction reversing switch (2) to position 'R'
in order to drive screws.
•
Set the direction reversing switch to position 'L' in
order to remove screws.
DRILLING
•
Rotate the torque adjustment ring (3) to the drilling
position.
Ensure that the direction reversing switch (2) is
always set to 'R' during drilling.
SWITCHING THE DEVICE ON AND OFF
Fig. A
•
Depress the on/off switch (1). It regulates the speed
of the appliance by transmitting power to the switch.
•
Release the on/off switch (1) to halt the drill chuck
immediately which will no longer run on.
•
Move the direction reversing switch (2) to the centre
in order to lock the appliance in its disabled state.
Only lay down the appliance when it has stopped running
completely. Do not place it on a dusty surface as
particles of dust could get into the mechanism.
CHARGING THE BATTERY
Fig. E
The included battery is delivered in non-charged
condition.
•
Only use the battery charger in a temperature range
between +10º to + 40º Celsius.
•
Only use the battery charger in dry, ventilated rooms.
CHARGING
•
Place the battery holder on a flat table and put the
battery in the battery holder. Pay attention to + and -
pole markings.
•
Put the adapter plug of the net adapter in the
connector on the side of the battery holder.
•
Put the net adapter in the socket.
•
The red charging lamp on the battery holder will
illuminate indicating the battery is being charged.
•
The charging process of a fully discharged battery will
take approximately 5 hours the first time and
afterwards approximately 3 hours.
5
Werbung
Inhaltsverzeichnis
