Axkid MOVEKID Bedienungsanleitung Seite 18

Installing Axkid MOVEKID car seat in
the vehicle
Before installing AXKID MOVEKID, make sure you have installed the lower tethers or lower tether anchorages in your vehicle. See section
about Lower Tether Anchorages and Installing lower tethers in this manual for more information and installation instructions.
1
Unzip the zipper and open the belt clamp lid (P).
Place the Axkid MOVEKID on the vehicle seat with the back of the car seat facing the front of the vehicle. Adjust the
2
legroom for your child by simply moving the car seat back and forth on the vehicle seat. Axkid MOVEKID can be
installed tight against the vehicle seat back but may never be installed with the heel (I) hanging over the edge of the
vehicle seat. Make sure that the vertical line (J) on the heel (I) never crosses the edge of the vehicle seat.
Adjust the angle of the car seat by choosing a suitable recline position with the recline angle adjuster (T). For maximum
safety, choose a position as upright as possible while also ensuring that your child' s head does not fall forward when
sleeping. For both comfort and safety reasons, the recline angle should be adjusted to a more upright position as your
child grows. Note that when tensioning the lower tethers (N), the car seat will be slightly more reclined as it sinks into the
vehicle seat cushion. When installing Axkid MOVEKID in a front passenger seat it is possible, but not necessary, for the
back of the car seat to have contact with the dashboard.
Open the belt clamp (O). Pull out an arm length of the vehicle seat belt and thread it through the seat belt slot (D) closest
3
to you. Route the belt through the belt clamp (O) and thread it through the seat belt slot (D) on the opposite side. Con-
nect the vehicle seat belt with the seat belt buckle and pull hard on the shoulder part of the vehicle seat belt to remove
all slack and to fasten the car seat, the harder you pull the firmer the installation. To give an even more firm and stable
installation, press down on the car seat while pulling the vehicle belt. When the car seat is firmly fastened, close the belt
clamp (O) and lock the vehicle seat belt in position. Make sure that both the shoulder and lap belt is locked together in
the belt clamp (O). Close the belt clamp lid (P) and close the zipper.
Attach the metal clips (L) to the metal clip connectors (K) on each side of the child seat (or connect the metal clips (L) to
4
the anchorages in your vehicle if lower tether anchorages is used for installation. See section Installing lower tethers
in this manual for more information). Press down on the top of the car seat while tensioning the lower tethers (N). By
tensioning the lower tethers (N) you also set the final recline angle of the car seat. Keep pushing down and tensioning
the car seat until it is firmly fastened, and you have achieved a suitable recline angle.
Pull out the support leg (Q) from the car seat. Push the support leg button (R) and pull the support leg (Q) downwards
5
until it is in contact with the vehicle floor. Let go of the support leg button (R) and lift the car seat upwards to further ex-
tend the support leg (Q) until you hear a click. The support leg (Q) should now be locked and firmly pressed against the
vehicle floor. Make sure that the support leg (Q) is angled about 10° towards the front of the vehicle. Check the vehicle
seat belt again to make sure that it is still firmly tensioned and that no slack has occurred in the hip belt while tensioning
the lower tethers and support leg. If the vehicle belt has lost some tension, simply re-tension it by repeating step 2 of this
guide without disconnecting the lower tethers.
Push the ASIP pad (H) into the slots on the ASIP connector (M) and slide downwards, the ASIP pad (H) will click into
6
place. If there is a plastic cover on the ASIP connector (M), remove it and place it on the ASIP connector (M) on the
opposite side of the seat before fitting the ASIP pad (H). Make sure the ASIP pad (H) is attached on the side of the Axkid
MOVEKID car seat that is closest to the vehicle door.
18