RS Pro RS MT-6600 Bedienungsanleitung Seite 7

Multifunction Installation Tester/English
5.1.2-Displayed icons (symbols) and messages in LOOP/PFC function
:Indicates the correct input terminal connectivity. The user should connect the test leads
to the appropriate terminals.
:Indicates L connection is conn
:Indicates no connection on the
If the wiring condition is other than normal, the Tester is limited on its measurements that can be performed.
Notes:
• Will not detect two hot wires in a circuit.
• Will not detect a combination of defects.
• Will not detect reversal of grounded and grounding conductors
:Indicates the battery status.
:100%
:80%
:50%
:20%
:Low Battery
:Indicates high temperature and therefore cannot make any measu
Message:
Measuring: Function in use - measurement being carried out
RCD Trip: During the measurement, the RCD has tripped therefore no test result obtained
-Noise-: Appears during the No Trip Loop Measurement, and indicates that the displayed value may not be
accurate due to "mains" interference - test to be
5.1.3-Displayed icons (symbols) and messages in RCD function
: Indicates the correct input terminal connectivity. The user should connect the test leads
to the appropriate terminals.
: Indicates L connection is connected on the N input terminal a
: Indicates no connection on the PE input terminal
If the wiring condition is other than normal, the Tester is limited on its measurements that can be performed.
Notes:
• Will not detect two hot wires in a circuit.
• Will not detect a combination of defects.
• Will not detect reversal of grounded and grounding conductors
: Indicates the battery status.
: 100%
: 80%
: 50%
: 20%
10
ected on the N input terminal and vice-versa
PE input terminal
.
rements
repeated
nd vice-versa
.
: Low Battery
: Indicates high temperature and therefore cannot make
Message:
Half: Appears during the auto test when rcd has operated on the
Half Trip: Appears during the manual test when rcd has operated on the x ½ test
UL OVER: Appears when UF voltage exceeds the previously set UL
50V) The user must check the impedance between
5.1.4-Displayed icons (symbols) and messages when using the LOW OHM and CONTINUITY functions
Symbol:
: Indicates correct input terminal connectivity. The user should connectthe test leads to the
appropriate terminals indicated by color coding.
: Low Battery (The icon will be ashing along with the beep so
: The resistance of the test leads are included in the test measurement
: The resistance of the test leads are not included in the test measurement
5.1.5-Displayed icons (symbols) and messages when using the RE functions
: Indicates correct input terminal connectivity. The user should connect the test leads to
the appropriate terminals indicated by color coding.
: Low Battery (The icon will be ashing along with the beep so
: The resistance of the test leads are included in the test measurement
: The resistance of the test leads are not included in the test measurement
5.1.6-Displayed icons(symbols) and messages in INSULATION function
: Indicates correct input terminal connectivity. The user should connect the test leads to
the appropriate terminals indicated by color coding.
: Low Battery (The icon will be ashing along with the beep so
: Indicates high voltage (125V, 250V,500V or 1000V) at probe terminals, Use caution
5.2-Using the LOOP/PFC Function
1-Before you do a loop impedance test, use the zero adapter to
and hold F4 button for more than two seconds until the
the lead resistance, stores the reading in memory, and subtracts it from readings. The resistance value is
saved even when the power is turned o so it is unnecessary to repeat the operation each time you use the
tester with the same test leads or mains cord.
Note: Be sure the batteries are in good charge condition before you
2-You can select UL Voltage by Pressing and hold F3 button for more than two seconds (25V or 50V).
Multifunction Installation Tester/English
any measurements
x ½ test
voltage. (UL voltage can be set to 25V or
L-PE
und).
und).
und).
zero the test leads or the mains cord. Press
ann unciator appears. The tester measures
zero the test leads.
11