Makita UV001G Betriebsanleitung Seite 16

The working depth can be adjusted in the range of
between -12 mm and 5 mm.
When you turn the adjusting dial to the far left position, the
working depth becomes the shallowest (5 mm from the
ground). When you turn the adjusting dial to the far right
position, the working depth becomes the deepest (-12 mm
from the ground). When you set the adjusting dial to the
upper center position, the working depth becomes 0.
The table below shows the relationship between the
number in the figure and the approximate working depth.
► Fig.15
Number
(1)
(2)
(3)
(4)
(5)
NOTE: The working depth can be set in 1 mm
increments.
NOTE: The working depth figures should be used just
as a guideline. Depending on lawn or soil conditions,
the actual working depth may become slightly differ-
ent from the set depth.
NOTE: Try a test operation in a less conspicuous
place to get the desired depth.
NOTE: When you turn the adjusting dial to the right
and set it to the lower scale of the machine, the work-
ing depth is set to -12 mm.
If the set working depth cannot be obtained when
you set the adjusting dial to the lower scale of the
machine depending on the conditions such as lawn
environment or wear of scarifier blades, you can
operate the machine with a setting one step deeper
by turning the adjusting dial to the right beyond the
lower scale.
► Fig.16: 1. Adjusting dial 2. Lower scale
Adjusting the handle height
The handle height can be adjusted in two levels.
1. Hold the middle handle, and then turn the knob 90°
while pulling the knob on the lower handle to release the
locking pin. Perform the same procedure on the other side.
► Fig.17: 1. Lower handle 2. Knob
NOTE: Supporting the handle makes it easier to
release the locking pin when pulling the knob.
2.
Adjust the handle height, and then turn the
knob on both sides 90°. Make sure that the knobs are
securely fixed.
► Fig.18: 1. Knob
Using the rear discharge
Using the rear discharge allows you to discharge the cut
grass to the ground from the rear side of the machine
without gathering the cut grass in the grass basket.
When you operate the machine using the rear dis-
charge, be sure to remove the grass basket, and close
the rear cover.
Working depth
5 mm
0 mm
- 4 mm
- 8 mm
- 12 mm
16 ENGLISH
Electronic function
The machine is equipped with the following electronic
functions.
• Electric brake
This machine is equipped with an electric brake. If
the machine consistently fails to quickly stop the
scarifier blades after releasing the switch lever,
have the machine serviced at Makita Authorized
Service Center.
OPERATION
Operating the machine
WARNING:
Before operating the machine,
remove sticks and stones from the work area.
Also, remove any weeds from the work area in
advance.
WARNING:
Always wear the safety goggles or
safety glasses with side shields when operating
the machine.
CAUTION:
If the cut grass or foreign object
blocks up inside of the machine body, be sure to
remove the battery cartridges and wear gloves
before removing the grass or foreign object.
NOTICE:
Use this machine only on lawns. Do not
use this machine on weeds.
► Fig.19
NOTICE:
Before operating the machine, be sure
to mow the lawn to a height of approximately 20
mm to 30 mm. If the lawn is too long, it may interfere
with the operation of the machine.
Hold the handle firmly with both hands when operating
the machine. The operating speed guideline is approxi-
mately 5 to 8 meters per 10 seconds.
► Fig.20
NOTE: When working on dense lawn, if a poor finish
is found after operation, or decrease of the motor
speed is found during operation, decrease the operat-
ing speed lower than recommended in this manual, or
set the working depth shallower.
Use the marks on the front side as a guide for working
width.
► Fig.21: 1. Working width 2. Mark
Periodically check the grass basket for cut grass. Empty
the grass before it becomes full. Before each periodic
check, be sure to stop and turn off the machine.
NOTICE:
Using the machine with a full grass
basket prevents the scarifier blades from rotating
smoothly and puts extra load on the motor, which
may result in a breakdown.