cecotec READY WARM 6600 CERAMIC STYLE SMART Bedienungsanleitung Seite 17

ENGLISH
Turn on the main switch located at the back of the device.
Press the On/off button to start the heater and press the mode button to select the desired
mode.
Select the temperature using the direction buttons to increase or decrease the temperature.
The temperature can be adjusted from 10 to 35 º.
When the set temperature is higher than the room temperature, the device will start heating
and the Mode indicator light will light up.
Press the mode button once or twice to start the heating directly. Pressing the button once will
start the low-temperature setting and pressing it twice you will start the high-temperature
setting.
Press the timer button to set the timer from 0 to 8 hours.
Press the oscillation button to operate the device with oscillation.
Press the On/off button to switch the device off. The fan blade indicator light will light up and
after 30 seconds, the device will switch off.
Oscillation button
Press the oscillation button to turn the oscillation function on and off.
Timer function
This function can be operated under any mode. The timer function allows you to set the
operation time from 1 hour to 8 hours. Every time the timer button is pressed, the operation
time will increase 1 hour. Once the timer has been set, the timer will count hour by hour, showing
the remaining time on the screen. Once this time is completed, the device will turn off itself.
Pressing the timer button once more after the screen shows 8 hours will reset the heater to
continuous operation.
Thermostat instructions
Select the temperature using the direction buttons to increase or decrease the temperature.
When the set temperature reaches the same or lower temperature than the room, the heater
will stop operating, but the fan will continue working to allow the product to cool down and
maintain the temperature.
When the set temperature is 2 degrees higher than the room temperature, the device will
start running in low temperature mode, and if it is 4 degrees lower it will start running in high
temperature mode.
Temperature can be set from 10 to 35 º.
Remote control
This remote control uses a Lithium battery CR2025 3V.
Any function set with the remote control will work identically as if the user had used the
control panel.
32
READY WARM 6600 CERAMIC STYLE SMART
Overheat protection
The device includes a overheat-protection system that switches the device off in case of an
overheating. For example, in case the air outlets were partially or totally clogged. In that case,
unplug the device, let it cool down for 30 minutes and remove the object clogging the vent.
Then, start the device again as described above. The device should operate normally now. In
case the problem persists, contact Cecotec's customer service for assistance.
The security push button stops the device in case of a tip-over.
4. CLEANING AND MAINTENANCE
Disconnect the appliance from the power supply, turn it off and allow it to cool down before
cleaning or storing it.
Use a soft, damp cloth to clean the product's surface.
Clean dust from the device's surface and air outlets regularly.
Clean and store the device in a safe, dry place if it is not going to be used for a long period of
time.
Do not immerse heater in water or allow water to drip into the interior of the heater, as this
could create an electric shock hazard.
Avoid the use of abrasive cleaning agents or scouring pads as these could damage the product.
The power cord should not be in contact with sharp edges, and it should not be compressed by
heavy objects. Store the cord in a clean, dry location always away from metal objects. Always
check the plug before use to assure metal items haven't become attached.
Do not place any heavy items on top of appliance during storage as this may result in possible
damage of appliance.
To disassemble the filter, press both upper tabs and remove the cover. Shake and clean the
filter with a damp cloth. Do not wash it.
5. TECHNICAL SPECIFICATIONS
Product reference: 05378
Product: ReadyWarm 6600 Ceramic Style Smart
2000W, 220-240 V~, 50 Hz
Made in China | Designed in Spain
Power Supply: AC 220-240V ~ 50Hz
Power: 2000 W
ENGLISH
READY WARM 6600 CERAMIC STYLE SMART
33