Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
•
For children safety reasons do not leave poly-
ethylene bags, used as a packaging, unat-
tended.
•
Attention! Do not allow children to play with
polyethylene bags or film. Danger of suf-
focation!
•
Do not immerse the motor unit in water or
any other liquids; do not wash it under water
jet. Clean the motor unit with a slightly damp
cloth, and then wipe it dry.
•
If water and juice gets into the motor unit,
switch the unit off and apply to an authorized
service center.
•
Do not use the unit, if the power cord, plug
or other removable parts are damaged, if the
unit works improperly or after it was dropped.
Do not try to repair the unit by yourself; in
case of damage apply to the authorized ser-
vice center.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE USING THE UNIT FOR THE FIRST
TIME
After unit transportation or storage at low
temperature it is necessary to keep it for at
least two hours at room temperature before
switching on.
Remove all stickers and packaging elements
–
that can prevent unit operation.
Check, whether your home mains voltage
–
corresponds to the unit operating voltage.
–
Wipe the motor unit (1) with a slightly damp
soft cloth and then wipe dry.
Disassemble the juicer. Wash all removable
–
parts with warm water and a neutral deter-
gent, then rinse thoroughly and dry.
Place the unit on a flat stable and dry surface
–
away from sources of heat, moisture, open
flame and direct sunlight.
Assembling the unit
Important! Make sure that silicone gasket
(14) is set properly in the bottom part of the
processing bowl (4). The silicone gasket
must seal the pulp channel tightly, otherwise
leakeage of juice/water from the bowl may
cause damage to the unit. The gasket (14)
has ledges along the base perimeter for
secure fitting.
VT-1602.indd 4
When cleaning the unit remove the silicone
gasket.
If water or juice gets into the motor
unit, switch the unit off and apply to the
authorized service center.
Set the processing bowl (4) on the motor unit
–
(1), matching the "unlocked"
the bowl and the motor unit, then turn the
bowl clockwise with a slight effort till the
«locked»
symbols match each other.
Install the separator (5) into the processing
–
bowl (4).
Install the mesh filter (6) into the processing
–
bowl, matching the marks (red dots) on
the mesh and processing bowl (4).
Note: Do not use the slow juicer, if there is any
mechanical damage of the mesh filter (6).
–
Install the screw (7) into the mesh (6), apply-
ing little effort; turn it slightly to provide
secure fitting if necessary.
Install the lid (8) on the processing bowl (4),
–
matching the marks on the lid and the
bowl, then turn the lid clockwise until click-
ing, so that the lock (9) arrow points at the
symbol .
USING THE SLOW JUICER
Important! Before switching the unit on,
make sure that all parts are installed
properly. Do not switch the unit on without
food.
Fruit, vegetables and berries intended for
processing must be fresh.
Before juice extraction remove inedible parts
–
from vegetables or fruits, such as stems,
hard peel or stones, for example, of cherry
or peach.
Wash fruit/vegetables and cut them into
–
pieces matching the feeding chute (10).
Place the unit on a flat stable surface.
–
Place the containers (12, 13) under the juice
–
and pulp outlets.
Insert the power plug into the mains socket.
Switch the slow juicer on by setting the
–
switch (3) to the ON position.
Note:
The unit will be switched on only if all the
removable parts are installed properly, and the
lid (8) is fixed with the lock (9).
4
symbols on
19.10.2012 12:32:50
Werbung
