Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PUNCH-IN/OUT RECORDING
Punch-in/out recording makes it possible. to re-record a short segment of an otherwise perfect track in.order to correct a
mistake or "brush up" an important passage. You "punch-in" at the point where you begin recording the new segment, and
"рипсп-ош" at.the-end of the new segment so that the previously-recorded material is not erased.
In addition to the normal functions of punching in and out, the unit also provides a rehearsal mode. This allows you to go through the whole
process of punching in and out without any actual recording taking place, so you c can practice the operation without ipai did your
precious recording.
Rehearsal Mode
1. To enter rehearsal mode, you must have at least one of the
REC SELECT switches setto a position otherthan OFF. Once
rehearsal mode has been entered, the REC SELECT switches
can be returned to OFF if necessary.
|
2. Press the REC/PAUSE and STOP button together. The red
ф REC/PAUSE indicator will turn yellow.
3. Performing any punch-in/out operations will not actually per-
form the recording, allowing you to.practice the operations.
4. To return to normal recording mode, press the REC/PAUSE
and STOP buttons together, and the REC/PAUSE indicator
will change back to red.
Punch-in/out
Using
the REC
SELECT
Switches
1. Ensure allthe REC SELECT switches are set to OFF, and the
MONITOR SELECT switch is set to MONITOR so you can
`
hear all the tracks.
2. Cue the tape to a few measures before the section to be re-
recorded begins. It's a good idea to reset the counter, and turn
the ZERO STOP on, so you can come back to this point.
3. Start the recorder running in the record-ready mode by
pressing REC/PAUSE then PLAY. The REC/PAUSE indica-
tor will flash, indicating that the transport is in record-ready
mode.
4. At a convenient break in the track, perform the punch-in, by
switching the REC SELECT switch for that track to the
appropriate record position. The REC/PAUSE indicator will
stop flashing, and light continuously. Any material now played
will be recorded (unless you're in rehearsal mode).
5. At the end of the re-recorded segment, punch-out by moving
the REC SELECT switch(s) back to OFF. The tape will
continue playing, and the REC/PAUSE indicator will begin to
flash.
Footswitch Punch-in/out
Don't forget, all of the. following steps can. be performed in
rehearsal mode (yellow REC/PAUSE indicator).
1. Plug a YAMAHA FC4 or ЕС5 (optional) footswitch into the
MT120S PUNCH ШО jack.
2. Setthe REC SELECT switch for the track to be punched in, to
the appropriate record position. The REC/PAUSE indicator
will start to flash slowly.
3. Press the REC/PAUSE
button to activate the rec/pause
mode. The REC/PAUSE indicator will start to flash faster.
4. To start the tape playing (not recording, yet), press the
footswitch (or press PLAY).
5. When you reach the punch-in point, press the footswitch
again. The indicator now lights continuously, and any material
now played will be recorded (unless you're in rehearsal
mode).
6. When you reach the point where you want to punch-out, press
`
the footswitch again. The indicator will go back to fast-
blinking. Steps 5 and 6 can be repeated several times, if
necessary.
i
7. When the tape reaches the end of the section requiring punch-
ins, press the STOP button.
TRACK 1
TRACK 2
TRACK 3
TRACK 4
STOP
All tracks monitored in PLAY- | The record mode is en
d
БАЛ
gage
BACK mode (the deck See
for track 3 only when the track
mode,
but the track
REC | 3 REC SELECT switch is set
SELECT
switches are set to
to an ON position.
Begin playback
It's a good idea to actually start playing a little
before the punch-in point.
23
Werbung
