EINHELL TKS 18/250 UV Bedienungsanleitung Seite 20

Anleitung TKS 18-250 UV SPK 1
GB
Wear a breathing mask
Noise emission values
Idle mode
Sound pressure level LPA 93,2 dB(A) 91,2 dB(A)
Sound power level LWA 106,2 dB(A) 104,3 dB(A)
The quoted values are emission values and not
necessarily reliable workplace values. Although there
is a correlation between emission and immission
levels it is impossible to draw any certain conclusions
as to the need for additional precautions. Factors
with a potential influence on the actual immission
level at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighboring
operations. Reliable workplace values may also vary
from country to country. With this information the
user should at least be able to make a better
assessment of the dangers and risks involved.
5. Technical data
AC motor 230V - 240V
Power P S1 1500 W S6 40% 1800 W
Idle speed n
0
Cutting-off wheel Ø 250 x Ø 30 x 2.4 mm
Number of teeth
Table size 660 x 440 mm
Table width extension, left/right 660 x 250 mm
Table length extension, rear 440 x 440 mm
Cutting height max. 73 mm/90°
53 mm / 45°
Height adjustment infinite 0 -73 mm
Tilting saw blade infinite 0° - 45°
Extractor socket
6. Before putting the machine into
operation
Unpack the bench-type circular saw and check it
for damage which may have occurred in transit.
The machine has to be set up where it can stand
firmly, e.g. on a work bench, or it must be bolted
to a strong base.
All covers and safety devices have to be
properly fitted before the machine is switched
on.
20
18.06.2004 9:10 Uhr
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
Important! Pull out the power plug before
carrying out any maintenance, resetting or
assembly work on the cutting-off machine!
7.1 Assembling the base frame (Fig. 17/18)
Turn the saw upside down and place it on the
floor.
Use the hex screws and nuts to fasten the four
wide side struts (41) loosely to the saw.
Now screw the four legs (40) loosely to the wide
side struts.
Then screw the four narrow side struts (42)
loosely to the four legs (40) and mount the
rubber feet (43) on the legs.
50Hz
Important! The shorter narrow struts (No. 2)
have to be used on the sides.
4800 min -1 Finally, turn the saw together with the base
frame upright and tighten all the screws and nuts
(Fig. 18).
24
7.2 Table width extension and length extension
7.2.1 Length extension table (Abb. 19/20)
Use the hex screws and nuts to fasten the table
length extension (36) loosely to the saw table (1)
Screw the supports (50) loosely onto the saw
housing and onto the table length extension.
Align the table length extension level with the
saw table (1).
Ø 36 mm
Finally, tighten all screws and nuts.
7.2.2 Width extension tables (Abb. 21/22)
Slide the width extension tables by their
connecting tubes into the prepared mounts as
far they will go, making sure that the numerical
scale always faces the front of the machine.
Secure the width extension tables in place with
the clamping screws (21) underneath.
7.3 Fitting / removing the saw blade guard (Fig. 3)
Mount the saw blade guard (2) on the splitter (5)
so that the screw fits through the hole (44) in the
Seite 20