Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
General
General
1
1
Disclaimer
Disclaimer
Compliance with the usage information for the
Safety measures
Compliance with the usage information for the
devices, modules and components is a prereq-
When operating electric devices, it is unavoidable
devices, modules and components is a prereq-
uisite for safe operation and attaining the stated
for certain parts of these devices and their com-
uisite for safe operation and attaining the stated
performance characteristics and product features.
ponents to conduct hazardous voltage. Conse-
performance characteristics and product features.
quently, severe bodily injury or material damage
Janitza electronics GmbH assumes no liability for
Janitza electronics GmbH assumes no liability for
bodily injury, material damage or financial losses
can occur if they are not handled properly.
bodily injury, material damage or financial losses
which result from disregard of the usage infor-
which result from disregard of the usage infor-
• Before making connections to the device and
mation. Make sure that your usage information is
mation. Make sure that your usage information is
its components, ground the device by means
readily available and legible.
readily available and legible.
of the ground wire connection, if present.
• Hazardous voltages can be present in all
Further usage information, such as the installation
Further usage information, such as the installation
circuitry parts that are connected to the power
manual or the user manual for the basic device,
manual or the user manual for the basic device,
supply.
can be found on our website, www.janitza.com
• There can still be hazardous voltages present
can be found on our website, www.janitza.com
under Support > Downloads.
under Support > Downloads.
in the device or the components even after
disconnection from the supply voltage (capac-
Copyright notice
Copyright notice
itor storage).
© 2023 - Janitza electronics GmbH - Lahnau.
© 2023 - Janitza electronics GmbH - Lahnau.
• Do not operate equipment with current trans-
All rights reserved. Any reproduction, processing,
former circuits when open.
All rights reserved. Any reproduction, processing,
distribution or other use, in whole or in part, is
distribution or other use, in whole or in part, is
• Do not exceed the limit values specified in the
prohibited.
prohibited.
user manual and on the rating plate! This must
also be observed during testing and commis-
sioning!
• Observe the safety information and warning
notices in the usage information associated
with the device and its components!
Incoming goods inspection
Incoming goods inspection
The prerequisites for trouble-free and safe oper-
The prerequisites for trouble-free and safe oper-
ATTENTION
ation of the devices, modules and components
ation of the devices, modules and components
ule
include proper transport, storage, setup and
include proper transport, storage, setup and
Improper handling or handling them too roughly
s
assembly, as well as proper operation and main-
assembly, as well as proper operation and main-
can destroy your devices and modules!
Contacts, bottom bolts and retaining brackets can
l
tenance.
tenance.
be damaged or broken off during mounting/dis-
bi-
Exercise due caution when unpacking and
Exercise due caution when unpacking and
mounting.
packing the device, do not use force and only use
packing the device, do not use force and only use
· Never touch or manipulate contacts!
t-
suitable tools.
suitable tools.
· Protect the contacts during handling, transport
Check:
Check:
and storage!
· Never mount/dismount devices/modules with
g-
• Visually inspect the devices, modules and
• Visually inspect the devices, modules and
force!
components for flawless mechanical condition.
components for flawless mechanical condition.
• Check the scope of delivery (see user manual)
• Check the scope of delivery (see user manual)
g-
for completeness before you begin installing
for completeness before you begin installing
your devices, modules and components.
your devices, modules and components.
If it can be assumed that safe operation is no
If it can be assumed that safe operation is no
e
longer possible, take your device, module or
longer possible, take your device, module or
is
component out of operation immediately! Secure
component out of operation immediately! Secure
against unintentional startup!
against unintentional startup!
s,
Subject to technical alterations.
Subject to technical alterations.
• Make sure that your device, module or compo-
• Make sure that your device, module or compo-
WARNING
nent matches the installation manual.
nent matches the installation manual.
• First make sure you have read and understood
• First make sure you have read and understood
Hazard due to disregard of warning and safety
information!
the usage information accompanying the prod-
the usage information accompanying the prod-
Disregard of the warnings and safety information
uct.
uct.
on the device itself and in the usage information for
• Keep the usage information associated with the
• Keep the usage information associated with the
the device and its components can lead to injuries
product available for the entire service life and
product available for the entire service life and
or even death!
pass it on to any possible subsequent users.
Observe the safety information and warning notic-
pass it on to any possible subsequent users.
es on the device itself and in the usage information
• Please find out about device revisions and the
• Please find out about device revisions and the
associated with the devices and their components,
associated modifications of the usage infor-
associated modifications of the usage infor-
such as:
mation associated with your product at www.
mation associated with your product at www.
· Installation manual.
janitza.com.
janitza.com.
· Installation supplement.
· User manual.
· Supplement Safety Information.
Disposal
Disposal
Please abide by national regulations! Dispose of
Please abide by national regulations! Dispose of
individual parts, as applicable, depending on their
individual parts, as applicable, depending on their
composition and existing country-specific regula-
composition and existing country-specific regula-
tions, e.g. as:
tions, e.g. as:
• Electronic waste
• Electronic waste
• Batteries and rechargeable batteries
• Batteries and rechargeable batteries
• Plastics
• Plastics
• Metals
• Metals
or engage a certified disposal
or engage a certified disposal
company to handle scrapping.
company to handle scrapping.
It can be assumed that safe operation is impossi-
It can be assumed that safe operation is impossi-
ble if the basic device, module or component, for
ble if the basic device, module or component, for
INFORMATION
example:
example:
System limits:
• Has visible damage.
• Has visible damage.
· If necessary, observe the installation manual for
• No longer functions despite an intact power
• No longer functions despite an intact power
transfer modules when setting up decentralized
supply.
supply.
measuring concepts.
• Was subjected to extended periods of unfa-
• Was subjected to extended periods of unfa-
· Before mounting, please check the number of
vorable conditions (e.g. storage outside of the
suitable modules for your measurement device
vorable conditions (e.g. storage outside of the
and module topology based on the respective
permissible climate thresholds without adjust-
permissible climate thresholds without adjust-
usage information.
ment to the room climate, condensation, etc.)
ment to the room climate, condensation, etc.)
or transport stress (e.g. falling from an elevat-
or transport stress (e.g. falling from an elevat-
For the scope of delivery of the 800-DI14 module,
ed position, even without visible external dam-
ed position, even without visible external dam-
refer to the user manual for the module. More infor-
age, etc.).
age, etc.).
mation on certain functions of the basic device with
modules can be found in the usage information of the
basic device.
Relevant laws,
Relevant laws,
standards and directive used
Qualified personnel
standards and directive used
To avoid bodily injury and material damage, only
Please see the declaration of conformity on our
Please see the declaration of conformity on our
qualified personnel with electrical training are
website (www.janitza.com) for the laws, standards
website (www.janitza.com) for the laws, standards
permitted to work on the basic device and its
and directives applied for the device by Janitza
and directives applied for the device by Janitza
components who have knowledge of:
electronics GmbH.
electronics GmbH.
• The national accident prevention regulations.
• Safety technology standards,
INFORMATION
INFORMATION
• Installation, commissioning and operation of
Our usage information uses the grammatical mascu-
Our usage information uses the grammatical mascu-
the device and the components.
line form in a gender-neutral sense! This form always
line form in a gender-neutral sense! This form always
refers equally to women, men and diverse. In order
refers equally to women, men and diverse. In order
WARNING
to make the texts more readable, distinctions are
to make the texts more readable, distinctions are
Risk of injury due to electric voltage or electric
not made. We ask for your understanding for these
not made. We ask for your understanding for these
current!
simplifications.
simplifications.
When handling electric currents or voltages, serious
bodily injury or death can result from:
· Touching bare or stripped leads that are energized.
· Device inputs that pose a hazard when touched.
Before starting work on your system:
· Disconnect the supply of power to the system!
· Secure it against being switched on!
· Check to be sure it is de-energized!
· Ground and short circuit!
· Cover or block off adjacent live parts!
3
Brief device description
3
Brief device description
The digital input module 800-DI14 extends the
The digital input module 800-DI14 extends the
functional range of the basic device (suitable basic
functional range of the basic device (suitable basic
Observe the installation instructions for your ba-
devices see user manual of the module) by an
devices see user manual of the module) by an
sic device (e.g. check bus connector installation!)
additional 14 digital inputs.
additional 14 digital inputs.
and mount the 800-DI14 module with the system
de-energized as follows:
The basic device detects an input signal
The basic device detects an input signal
at the digital input of the 800-DI14 module
at the digital input of the 800-DI14 module
when:
when:
· A voltage of at least 18 V and at most
· A voltage of at least 18 V and at most
28 V DC (typically at 4 mA) is present.
28 V DC (typically at 4 mA) is present.
Bottom bolt,
open
· A current of at least 0.5 mA and at most
· A current of at least 0.5 mA and at most
6 mA flows.
6 mA flows.
Bus connector
For voltages from 0 to 5 V and currents
For voltages from 0 to 5 V and currents
less than 0.5 mA there is no input signal.
less than 0.5 mA there is no input signal.
800-DI14 module
800-DI14 module
(without connection terminals)
(without connection terminals)
Bottom bolt,
Transmission error and material damage due to electrical malfunction.
Transmission error and material damage due to electrical malfunction.
open
With a cable length of more than 30 m, there is an increased probability of transmission errors and damage to
With a cable length of more than 30 m, there is an increased probability of transmission errors and damage to
the device due to atmospheric discharge!
the device due to atmospheric discharge!
Use shielded cables for the connections to the digital inputs and outputs!
Use shielded cables for the connections to the digital inputs and outputs!
Fig.: Module rear views (without connection terminals)
7 / 10
Intended use
The module /component
• is only intended for use in industrial areas.
• is intended as an expansion or transfer module
for measuring device and module topologies
with suitable basic devices (see user manual
of the respective module) in switchboard cabi-
nets and small distribution boards.
• Only mount with the basic device disconnect-
ed from the power supply (see "Mounting"
step). Observe the usage information belong-
ing to the basic device!
The basic device and the modules are not desig-
ned for mounting
• Not intended for installation in vehicles! The
use of the basic device with modules in
non-stationary equipment is considered to be
an exceptional environmental condition and is
only permitted by separate agreement.
• Not intended for installation in environments
with harmful oils, acids, gases, vapors, dusts,
radiation, etc.
• Not intended for installation in potentially
explosive atmospheres.
INFORMATION
INFORMATION
1. Press in the open bottom bolts on the rear of the
Observe the polarity of the supply voltage!
Observe the polarity of the supply voltage!
module.
2. If this has not yet been done, press the bus con-
Digital inputs
Digital inputs
Digital inputs
Digital inputs
(top of module)
(top of module)
bottom of module
nector (JanBus interface) included in the scope
bottom of module
of delivery into the sockets on the rear of your
1 - DI1
1 - DI1
1 - DI8
module.
2 - DI2
2 - DI2
2 - DI9
Bottom bolt,
pressed in
3 - DI3
3 - DI3
3 - DI10
4 - DI4
4 - DI4
4 - DI11
Bus connector
Twisted
5 - DI5
5 - DI5
5 - DI12
6 - DI6
6 - DI6
6 - DI13
7 - DI7
7 - DI7
7 - DI14
8 - C1
8 - C1
8 - C2
Supply
Supply
voltage
voltage
ATTENTION
ATTENTION
Bottom bolt,
pressed in
2 2
4
1 - DI8
2 - DI9
3 - DI10
4 - DI11
5 - DI12
6 - DI13
Press the bus connector
7 - DI14
contacts into the module
sockets
8 - C2
Supply
Supply
voltage
voltage
Werbung
Inhaltsverzeichnis
