WOLFF BS 125 Originalbetriebsanleitung Seite 16

5. Important components
1 Spindle locking button
2 Spindle
3 Supporftlange
4 Diamond disc
5 2-hole Adjusting nut *
6 2-hole spanner *
7 Supporpt late
Electronic signal display
8 Distance ring
11 Sliding on/off switch
12 Lever
13 Safety cover
14 Extractor connection piece
15 Segment for working near walls
(open by twisting)
16 Brush rim
6 Commissioning
6.1 Attachguard at the angle grinder
See illustration B on page 2.
- Push and hold the lever (12). Place the safety
guard (13) in the position indicated.
- Release the lever and turn the safety guard until
the lever engages.
- Make sure that the guard is placed securely:
The lever must engage and you should not be
able to turn the safety guard.
(Disassemble in reverse order.)
6.2 Dust extraction
Always use a suitable dust extraction system:
Connect an M-class vacuum cleaner to the
extractor connection piece (14).
For optimal dust extraction, use the connecting
sleeve #66218.
WOLFF recommend:
Wet-dry vacuum cleaner Starvac #60800
We recommend using an antistatic suction
hose Ø 35 mm.
Before plugging in, check to see that the rated
mains voltage and mains frequency, as stated
on the rating label, match with your power
supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
7.
See page 2.
switched off and the spindle at a standstill.
7.1 Locking the spindle
Press in the spindle locking knob (1) only when the
spindle is stationary!
- Press in the spindle locking button (1) and
7.2
To fit:
- Fit the support flange (3) on the spindle (2). The
- Lay 1 or 2 washers on the support flange,
- Lay the diamond disc (4) on the washers
- The 2 sides of the clamping nut (5) are different.
- Lock the spindle (see chapter 7.1). Turn the
Removal:
- Lock the spindle (see chapter 7.1). Turn the
7.4
The 2 sides of the 2-hole nut are different. Screw
the 2-hole nut onto the spindle as follows:
See illustration F on page 2.
- X) For thin grinding discs:
Releasing the 2-hole nut:
- Lock the spindle (see chapter 7.1). Turn the 2-
Attaching the accessory
Prior to any conversion work: Pull the mains
plug from the socket. The machine must be
turn the spindle (2) by hand until the spindle
locking button engages.
Fitting/removing the diamond cup wheel
See illustration A on page 2.
flange should not turn on the locked spindle when
properly attached.
depending on how much the diamond cup is
worn.
so (3) that it lies flat along the washers.
Screw the clamping nut onto the spindle so that
the band of the clamping nut (5) is centering the
diamond disc. (Picture F)
clamping nut (5) clockwise using the 2-hole
spanner (6) to secure.
clamping nut (5) anticlockwise using the 2-hole
spanner (6) to unscrew
Securing/Releasing the 2-hole nut
Securing the 2-hole nut (5):
The edge of the 2-hole nut (5) faces upwards so
that the thin grinding disc can be attached
securely.
Y) For thick grinding discs:
The edge of the 2-hole nut (5) faces downwards
so that the 2-hole nut can be attached securely to
the spindle.
hole nut (5) anticlockwise using the 2-hole
spanner (6) to unscrew.
- 16 -