WOLFF BS 125 Originalbetriebsanleitung Seite 14

b) Never place your hand near the rotating
accessory.
Accessory may kickback over your hand
c) Do not position your body in the area where
power tool will move if kickback occurs.
Kickback will propel the tool in direction opposite to
the wheel's movement at the point of snagging.
d) Use special care when working corners,
sharp edges etc.Avoid bouncing and snagging
the accessory.
Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause
loss of control or kickback.
e) Do not attach a saw chain woodcarving
blade or toothed saw blade.
Such blades create frequent kickback and loss of
control.
4.3 Safety Warnings Specific for Grinding
and Abrasive Cutting-Off Operations:
a) Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel.
Wheels for which the power tool was not designed
cannot be adequately guarded and are unsafe.
b) The grinding surface of the centre depressed
wheels must be mounted below the plane of
the guard lip.
An improperly mounted wheel that projects through
the plane of the guard lip cannot be adequately
protected.
c) The guard must be securely attached to the
power tool and positioned formaximumsafety,
so the least amount of wheel is exposed
towards the operator.
The guard helps to protect operator from broken
wheel fragments and accidental contact with wheel
and sparks which could ignite clothing.
d) Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel.
Proper wheel flanges support the wheel thus
reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different from
grinding wheel flanges.
e) Do not use worn down wheels from larger
power tools.
Wheel intended for larger power tool is not suitable
for the higher speed of a smaller tool and may
burst.
4.4 Safety Warnings Specific for Grinding
with Diamond Cup Wheels:
a) Always use undamaged wheel flanges that
are the correct size and shape for your
selected accessories.
The correct flanges support the accessories.
4.5 Weitere Sicherheitshinweise:
WARNING – Always wear protective
goggles.
.
Wear a suitable dust protection mask.
Do not use bonded discs.
Use elastic cushioning layers if they have been
supplied with the grinding media and if required.
Observe the specifications of the tool or accessory
manufacturer! Protect the discs from grease or
impacts!
Never use cutting discs for roughing work! Do not
apply pressure to the side of the cutting discs.
If accessories with threaded inserts are used, the
end of the spindle may not touch the base of the
hole on the grinding tool.
Make sure that the thread in the accessory is long
enough to accommodate the full length of the
spindle. The thread in the accessory must match
the thread on the spindle. (Technical Data).
Observe the specifications of the accessory
manufacturer! Protect the accessories from grease
and physical impact.
Accessories must be stored and handled with care
in accordance with the manufacturer's instructions.
Secure small workpieces. For example, clamp in a
vice.
The workpiece must lay flat and be secured
against slipping, e.g. using clamps. Large
workpieces must be sufficiently supported.
Damaged, eccentric or vibrating tools must not be
used. Only use accessories that are surmounted
by brushes of the safety guard.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
Read the operating instructions supplied with the
installed angle grinder.
Use of a fixed extractor system is recommended.
Always install an RCD with a max. trip current of
30 mA upstream. If the anglegrinder is shut down
via the RCD, it must be checked and cleaned.
See chapter Cleaning.
S-automatic safety clutch. When the safety clutch
responds, switch off the machine immediately!
A damaged or cracked additional handle must be
replaced. Never operate a machine with a
defective additional handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a
defective safety guard.
Secure small workpieces. For example, clamp in a
vice.
- 14 -