Bosch EXACT ION 18 V-LI 6-1500 WK Originalbetriebsanleitung Seite 17

OBJ_BUCH-2165-003.book Page 17 Thursday, March 16, 2017 3:22 PM
inserted in the power tool, it is held in position by means of a
spring.
– To remove the battery 12, press the unlocking button 13
and pull out the battery toward the front. Do not exert any
force.
Battery Charge-control Indication (yellow LED)
Battery Meaning
Charge-control
Indication 10
Flashing light + Battery Charging:
audio signal Only 6–8 more screwdriving operations
possible.
Continuous light Capacity no longer sufficient for a new
screwdriving operation or the machine
was subject to overload:
The machine can no longer be switched
on.
– Remove the battery and replace with
a fully charged one.
Flashing light The machine is overheated and out of
operation:
– Before restarting the operation of the
machine, wait until the flashing auto-
matically stops after a short period.
Operating and Storage Environment
The device is suitable exclusively for operation at enclosed
work sites.
For trouble-free operation, the permitted ambient tempera-
ture of the power tool should lie between 0 °C and +45 °C at
a permitted relative humidity of between 20 and 95 %, free of
condensation.
Suspension Device (see figure B)
With the utility clip 15, the machine can be attached to a sus-
pension device.
– Fasten the utility clip 15 to the machine by engaging it into
the fastening slots 16.
 Regularly check the condition of the utility clip and the
hook of the suspension device.
Adjusting the Worklight (see figure C)
– Press off the marking ring 18 with a thin screwdriver blade,
a knife, or similar.
– Using snap-ring pliers, slide the snap ring 19 toward the
rear onto the housing shell.
The two shell halves of the LED holder 17, which enclose the
worklight 6, can now be adjusted to any desired position.
– Pay attention not to damage the worklight cable and, with-
out kinking or bending it, slide it into the cavity 20 intend-
ed for it in the housing shell.
– Enclose the worklight 6 again with the two housing shells
of LED holder 17.
– Press the snap ring 19 and the marking ring 18 back to
their initial positions.
Bosch Power Tools
Configuring the Power Tool
With the BOSCH EXACT Configurator software, different pow-
er tool settings (e. g., speed, driving stages, repeat protec-
tion) can be configured. For this, the power tool must be con-
nected to a PC via the USB data port.
Note: Observe all safety warnings and instructions in the soft-
ware instruction manual.
Mounting the Angled Screw Head (see figure D)
On these industrial cordless angle wrenches, a fitting angled
screw head (see "Angled drive head", page 16) has to be
mounted first.
– Hold the power tool with the open-end spanner 22 by the
spanner flats 4 of the angled head flange.
 Never clamp the tool by the housing shells!
– Mount the angled screw head 3 onto the flange in the re-
quested position and tighten the sleeve nut with the open-
end spanner 21 via the spanner flats 5.
Hold the angled head flange with the open-end spanner 22
to prevent turning.
Adjusting the Angled Drive Head
The angled drive head 3 can be adjusted to a total of eight po-
sitions.
– Hold the power tool with the open-end spanner 22 by the
spanner flats 4 of the angled head flange.
 Never clamp the tool by the housing shells!
– Loosen the sleeve nut with the open-end spanner 21 by
the spanner flats 5. Adjust the angled drive head 3 in 45°
steps to the desired position and retighten the sleeve nut
again with the open-end spanner 21 by the spanner flats 5.
Hold the angled head flange with the open-end spanner 22
to prevent turning.
Changing Application Tools on the Screw Head
with External Square Drive (see figure E)
Inserting
– Press in the pin on the drive square of the tool holder 2,
e. g. using a small screwdriver, and slide the tool bit 1 over
the drive square. Pay attention that the pin engages in the
recess of the tool bit.
Removing
– Press in the pin in the recess of the tool bit 1 and pull the
tool bit out of the tool holder 2.
Changing Application Tools on the Screw Head
with Internal Hexagon (see figure F)
Inserting
– Insert the tool bit 1 into the internal hex socket of the tool
holder 2 until it can be felt to engage.
Removing
– Pull the tool bit 1 off of the tool holder 2 with the aid of pli-
ers, if necessary.
English | 17
1 609 92A 3U1 | (16.3.17)