Werbung
Verfügbare Sprachen
Verfügbare Sprachen
OBJ_BUCH-2165-003.book Page 16 Thursday, March 16, 2017 3:22 PM
16 | English
Industrial Cordless Angle Wrench EXACT ION
Battery (Not included in the standard delivery scope)
Permitted ambient temperature
– during charging
*
– during operation
and during storage
Recommended batteries
– GBA 18 V... (Battery pack L) (0 602 494 002)
– GBA 18 V... (Battery pack XL) (0 602 494 004)
Recommended chargers
Angled drive head (Standard delivery scope)
Straight drive head (Standard delivery scope)
A)
measured with Bosch angled drive head
* Limited performance at temperatures <0 °C
Article number 0 607 ...
Torque for hard/soft screwdriving
application according to ISO 5393
Tightening torque at the flange
Weight according to EPTA-Procedure
01:2014
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-2.
Typically the A-weighted sound pressure level of the product
is 70 dB(A). Uncertainty K=3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-2:
Screwdriving without impact: a
<2.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
1 609 92A 3U1 | (16.3.17)
6-1500 WK 8-1100 WK 12-700 WK 12-450 WK
°C
0...+45
°C
–20...+50
AL 18..
GAL 3680
Angled
Angled
drive head
drive head
1/4"
3/8"
... 453 617
... 453 620
Nm
20
Nm
20
kg
0.21
Assembly
Before any work on the power tool, remove the battery.
Battery Charging
Use only the battery chargers recommended by Bosch
for this power tool. Only these battery chargers are
matched to the lithium ion battery used in your machine.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
2
2
, K=1.5 m/s
.
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery (see figures A1 – A2)
The battery 12 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 13 unintentionally. As long as the battery is
Li-Ion
Li-Ion
Li-Ion
0...+45
0...+45
–20...+50
–20...+50
–
–
AL 18..
AL 18..
GAL 3680
GAL 3680
–
–
–
–
Angled
Angled
drive head
drive head
1/4"
QC 1/4"
... 453 618
... 453 630
20
20
20
20
20
20
0.21
0.22
0.21
Li-Ion
0...+45
–20...+50
–
–
AL 18..
GAL 3680
–
–
–
–
Straight
drive head
QC 1/4"
... 453 631
6
10
0.21
Bosch Power Tools
Werbung
