Werbung
Verfügbare Sprachen
Verfügbare Sprachen
45° angle settings.
•
Warning! You should replace the table in-
sert (52) immediately whenever it is worn or
damaged. To do so, undo the recessed head
screws in the table insert (52) and take the
table insert out of the turntable (17). To fit
the new table insert (52), proceed in reverse
order.
•
Warning! The work to change and align the
saw blade (7) must be carried out correctly.
6.11 Transport (Figs. 1-4)
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Press the machine head (4) downwards and
secure with the retaining pin (25). The saw is
now locked in its bottom position.
•
Carry the machine by the transport handle
(9).
•
To set up the equipment again, proceed as
described in section 5.2 + 5.3.
6.12 Operating the laser (Figs. 12, 23)
Switching on: Move the On/Off switch (36) to the
"
" position to switch on the laser (35). A laser
line is projected onto the material you wish to pro-
cess, providing an exact guide for the cut.
Switching off : Move the On/Off switch (36) to the
"OFF" position.
6.13 Operating the LED lamp (Figs. 12, 23)
•
For good illumination of the work area you
can use the LED lamp in addition to the room
lighting. The On/Off switch (24) for the LED
lamp is on the top of the machine head, bet-
ween the handle (1) and the mount for the
rechargeable battery (40).
•
Switching on: Switch position "
•
Switching off: Switch position "OFF"
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
Anl_TE_SM_36_10_L_Li_Solo_SPK13.indb 31
GB
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.Einhell.Service.com
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
"
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
9. Storage
Store the equipment and accessories in a dark
and dry place at above freezing temperature.
The ideal storage temperature is between 5 and
30 °C. Store the electric tool in its original pa-
ckaging.
- 31 -
10.07.2023 11:28:35
Werbung
