Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.5 Cross cut 90° and turntable 0° - 45°
(Fig. 1-4, 18)
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Turn the turntable (17) and scale pointer (15)
to the desired angular setting on the scale
(16).
•
Retighten the locking screw (14) to secure the
turntable (17) in place.
•
Cut as described in section 6.4.
6.6 Miter cut 0°- 45° and turntable 0°
(Fig. 1-4, 19)
The crosscut saw can be used to make miter cuts
of 0- 45° in relation to the work face.
•
If necessary, dismantle the clamping device
(8) from the left side of the saw table (18) or
mount on the right-hand side of the fixed saw
table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (17) in 0° position.
•
Set the miter angle on the machine head as
described in 5.5.
•
Cut as described in section 6.4.
6.7 Miter cut 0°- 45° and turntable 0°- 45°
(Fig. 1-4, 20)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° in relation to the work surface,
with simultaneous setting of the turntable from
0°-45° to the left or 0°-45° to the right in relation to
the stop rail (double miter cut).
•
If required, dismantle the clamping device
(8) or mount on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (17) by undoing the
locking screw (14).
•
Use the handle (1) to adjust the turntable (17)
to the angle required (in this connection see
also section 6.5).
•
Retighten the locking screw (14) to secure the
turntable in place.
•
Adjust the miter angle on the machine head
Anl_TE_SM_36_10_L_Li_Solo_SPK13.indb 30
GB
and the stop rail as described under points
5.5 and 6.3.
•
Cut as described in section 6.4.
6.8 Limiting the cutting depth (Fig. 21)
•
The cutting depth can be infinitely adjusted
using the screw (27). To do so, undo the
knurled nut on the screw (27). Turn the screw
(27) in or out to set the required cutting depth
and then retighten the knurled nut on the
screw (27).
•
Check the setting by completing a test cut.
6.9 Sawdust bag (Fig. 8)
The saw is equipped with a sawdust bag (22).
The sawdust bag (22) can be emptied by means
of a zipper at the bottom.
6.10 Replacing the saw blade (Fig. 1, 22)
•
Danger! Remove the rechargeable battery
before you replace the blade.
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Press the spindle locking system (5) with
one hand while positioning the combination
key (42) on the flange bolt (31) with the other
hand. The spindle locking system (5) enga-
ges after no more than one rotation.
•
Now, using a little more force, slacken the
flange bolt (31) in the clockwise direction.
•
Turn the flange bolt (31) right out and remove
the washer (33) and the outer flange (32).
•
Take the blade (7) off the inner flange and pull
out downwards.
•
Carefully clean the flange bolt (31), washer
(32), outer flange (33) and inner flange.
•
Fit and fasten the new saw blade (7) in rever-
se order.
•
Important! The cutting angle of the teeth,
in other words the direction of rotation of the
saw blade (7) must coincide with the direction
of the arrow on the housing.
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Warning! Every time that you change the
saw blade, check that the saw blade guard
(6) opens and closes again in accordance
with requirements. Also check that the saw
blade (7) spins freely in the saw blade guard
(6).
•
Warning! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (52) in both perpendicular and
- 30 -
10.07.2023 11:28:35
Werbung
