Hama RCR 110 Bedienungsanleitung Seite 6

Setting the alarm time
• Repeatedly press the MODE button (4) to access alarm mode 1
(AL1) or 2 (AL2).
• Press and hold the MODE button (4) to set the alarm time for
the alarm displayed. The hours display begins to ash.
• Press the p button (3) or the  button (2) to select the hour
for the alarm time and con rm your selection by pressing the
MODE button (4). The minutes display begins to ash.
• Repeat the process to set the minutes for the alarm time.
• Press the MODE button (4) repeatedly to also set the other
alarm mode or return to the temperature display.
Activating/deactivating the alarm
• Press the button (9) repeatedly to activate/deactivate alarm
1 or alarm 2.
• If an alarm is activated, the corresponding symbol
be displayed.
Stopping the alarm/snooze function
• If the alarm is triggered, the alarm symbol
ash and an alarm will sound.
• Press the button (9) to stop the alarm. Otherwise, it will stop
automatically after 4 minutes.
Note – Snooze function
While the alarm signal is sounding, press the LIGHT-SNOOZE
button (1) to activate the snooze function. The alarm symbol
(7) / and Z will begin to ash. The alarm signal will be
z
stopped for 4 minutes, after which it will sound again.
5.5. Dual Time settings and display
• Dual Time allows you to set and display a second, completely
independent time (8).
• Press the MODE button (4) repeatedly until SECOND TIME
is displayed.
• Press and hold the MODE button (4) for approximately 3
seconds. The hours display begins to ash.
• Press the p button (3) or the  button (2) to select the hour
and con rm your selection by pressing the MODE button (4).
The minutes display begins to ash.
• Repeat the process to set the minutes.
• To select the individual values, press the p button (3) or the 
button (2) and con rm each selection by pressing the MODE
button (4).
5.6. Backlight
If you press the LIGHT-SNOOZE button (11), the display will light
up for approx. 5 seconds.
5.7. Projection
Activating/deactivating
Power supply from  batteries
• Press the LIGHT-SNOOZE button (11) to project the display onto
the wall or ceiling for ve seconds.
Power supply from  batteries + mains:
• Slide the CONTINUE PROJECTION sliding switch (9) up
towards
• Slide the CONTINUE PROJECTION sliding switch (9) down/
away from
Projection settings:
• Turn the projection arm (8) forward/back to project the display
/ will
onto the wall or ceiling.
• Press the FLIP button (7) to rotate the projection by 180°.
• Turn the ROTATE control dial (12) to further rotate the projection
by up to +/–90°.
/ will begin to
• Turn the FOCUS control dial (13) to focus the projection.
• Press and hold the FLIP button (7) for approx. 3 seconds to
switch the projection between displaying the time and displaying
the time and temperature.
Note – Projection
• At a distance from the projection lens to the wall/ceiling of
• By default, the projection shows the time. See the instructions
6. Care and Maintenance
Only clean this product with a slightly damp, lint-free cloth and do
not use aggressive cleaning agents. Make sure that water does not
get into the product.
Note
Disconnect the device from the power supply before cleaning it
or if it is not going to be used for a long period of time.
7. Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no
warranty for damage resulting from improper installation/mounting,
improper use of the product or from failure to observe the operating
instructions and/or safety notes.
to set the projection to sustained mode.
to deactivate sustained mode.
about 2 m / 4 m, the size of the display projection on the wall
is about 10 cm / 18 cm.
above to set the projection to alternate between the time and
the temperature.
5