Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Membran-Injektionssystem
MIS90S
Lagerung
HINWEIS!
Beschädigung durch unsachgemäße Lagerung!
Bei unsachgemäßer Lagerung können Sachschäden in erheblicher Höhe ent-
stehen.
• Membran-Injektionssystem vor der Montage vor Beschädigungen, Feuchte und
Verunreinigungen schützen. Es dürfen nur unbeschädigte Teile montiert wer-
den.
• Die Lagerung des Membran-Injektionssystem muss so erfolgen, dass dieser kei-
nen zu niederen Temperaturen (<5 °C) und höheren Temperaturen (>30 °C) so-
wie keiner direkten Sonneneinstrahlung ausgesetzt ist.
Entsorgung
Sofern keine Rücknahme- oder Entsorgungsvereinbarung getroffen wurde, zer-
legte Bestandteile nach sachgerechter Demontage der Wiederverwertung zufüh-
ren:
• Metallische Materialreste nach den geltenden Umweltvorschriften verschrotten.
• Elastomere nach den geltenden Umweltvorschriften entsorgen.
• Kunststoffe nach den geltenden Umweltvorschriften entsorgen.
• Verpackungsmaterial nach den geltenden Umweltvorschriften entsorgen.
• Ausgehärtete Expansionsharzreste nach den geltenden Umweltvorschriften ent-
sorgen (Hausmüll/Gewerbeabfall).
• Restentleerte Verpackung des Expansionsharz nach den geltenden Umweltvor-
schriften entsorgen (gelbe Tonne/Sack).
EN Safety Instructions and Information
Target Group
The installation may only be carried out by technical experts.
Qualified and trained individuals carrying out installation must have
• knowledge of general safety and accident prevention regulations as amended,
• knowledge of how to use safety equipment,
• knowledge of how to use hand tools and electric tools,
• knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfilling utility trenches as amended,
• knowledge of the regulations and installation guidelines of the supply company
as amended,
• knowledge of the waterproof concrete directive and building waterproofing
standards as amended.
General information and intended use
In line with their intended use, our products have been developed solely for instal-
lation in buildings made of state-of-the-art materials. Insofar as no express written
confirmation has been provided by us, we do not accept any liability for any other
purposes or purposes going beyond the above.
For warranty conditions, please see our current General Terms and Delivery Condi-
tions. We explicitly draw your attention to the fact that no warranty whatsoever
applies for any subsequent damage occurring as a result of failure to follow the
installation instructions or if our products are used incorrectly or combined with
third-party products.
MIS90S suitable for inclined building entry through the wall or floor slab for the
reliable sealing of all water and telecommunications lines without additional
shrinking using a sealing sleeve. It is possible to accommodate 1 cable/pipe with
24 - 52 mm diameter, or 1 cable/pipe with 24 - 40 mm diameter and 3 cables
with 7 - 12 mm diameter, or 1 cable/pipe with 13 - 21 mm diameter, 3 cables
with 7 - 13 mm diameter and 1 cable with 5 - 13 mm diameter.
Safety
This section provides an overview of all the main safety aspects for optimum pro-
tection of personnel and a safe installation process.
A failure to observe the instructions and safety information set out here may re-
sult in significant hazards.
During installation of the Membrane injection system it is imperative to observe
the relevant professional association rules, the VDE provisions, the relevant na-
tional safety and accident prevention regulations and your company's guidelines
(work and procedure instructions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
When dealing with expansion resin, the following points must be strictly ob-
served:
Expansion resin: Tangit iM 3000
Component B: Contains isocyanate.
Observe manufacturer's instructions and the manufacturer's safety data sheet as
amended.
Harmful. Contains Diphenylmethane diisocyanate, isomers and homologues.
The product falls within the scope of applicability of Regulation (EC) 1907/2006
(REACH), Annex XVII, No. 74, Item 1(b). Effective 24 August 2023, appropriate
Art. Nr.: 5090032046 Rev.: 03/2023-05-03
training must be conducted prior to any industrial or commercial application.
Further information at: https://www.feica.eu/PUinfo
• Harmful by inhalation
• Irritating to eyes, respiratory system and skin
• May cause sensitisation by inhalation
• Keep out of the reach of children
• In case of contact with eyes, rinse immediately with plenty of water and seek
medical advice
• After contact with skin, wash immediately with plenty of water and soap
• Wear suitable glove
• In case of accident or if you feel unwell, seek medical advice immediately (show
label on cartridge if possible)
• Processing temperature: +5 °C to +30 °C, optimum: +15 °C to +25 °C
The following instructions are to be observed prior to installa-
tion of the Membrane injection system MIS90S:
WARNING!
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and property dam-
age.
• Observe the nationally applicable laying and filling regulations for pipes and ca-
bles.
• Seal the underground and cable substructure well prior to laying pipes or cables
so that the latter cannot subside.
NOTICE!
No sealing due to incorrect installation!
Improper installation can result in damage.
• Diamond core bits for dry cutting are available (e.g. Hilti) for basements with
masonry walls. Handheld drills can be used.
• Hammer drills with core drills cannot be used in the no-dig scenario due to the
risk of extensive spalling of the basement wall with exterior waterproofing.
• If spalling and breaks occur more extensively around the drilled hole, the wall
surface and coating must be properly repaired and the waterproofing of the
wall surface and coating must be restored according to DIN 18533.
• Minimum bending radiuses of the cables and pipes must be observed.
• All surfaces must be clean, firm and free of dust and grease.
• Do not use cleaning agents containing solvents to clean the Membrane injec-
tion system. We recommend using the cable cleaner KRMTX.
• For details of other accessories and further information, see www.hauff-tech-
nik.de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
WARNING!
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property dam-
age.
• Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the rele-
vant provisions, standards and regulations, skilled experts are able to carry out the
work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
NOTICE!
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
• When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport dam-
age. In the event of transport damage being visible from the outside, proceed as
follows:
• Do not accept the delivery or only do so subject to reservations.
• Make a note of the extent of damage in the transport documentation or deliv-
ery note provided by the transporter.
• Submit a claim for every defect as soon as it has been identified.
• Claims for damages can only be asserted within the applicable claim
period.
7
Werbung
