Optional Accessories - Makita BL1055B Betriebsanleitung

Vorschau ausblenden Andere Handbücher für BL1055B:

Betriebsanleitung (180 Seiten)

Inhalt

Seite von 73

/ 73
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

Battery BL1055B

While the battery BL1055B is unplugged, press the power but-

ton. The battery capacity indicator light up for a few seconds.

► Fig.24: 1. Battery capacity indicator

Meaning of the indicator lamp

Indicator lamps

Lighted

Off

Battery protection system

The device is equipped with a battery protection sys-

tem. This system automatically cuts off power to the

motor to extend battery life.

If the remaining battery capacity is too low, the device

will not operate. When you turn the device on, the motor

will run again, but stops soon. In this situation, remove

and recharge the battery cartridge.

MAINTENANCE

CAUTION:

Always be sure that the jacket is

switched off and the battery cartridge or battery

BL1055B is removed before attempting to perform

inspections or maintenance.

CAUTION:

If the jacket/vest does not switch

on or any fault is found with a fully charged bat-

tery cartridge, clean the terminals of the battery

holder and the battery cartridge. If the jacket still

does not work properly, stop using the jacket/vest

and contact our authorized service center.

NOTICE:

Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Cleaning the fan unit

Wipe off dirt, dust, oil, grease .etc, with clean dry cloth.

To clean the fan blade, remove the ring and unhook the

housing from the cover using slotted screwdriver or sim-

ilar. There are three hooks on the housing. Unhook them

little by little in rotation so as not to break the hooks.

► Fig.25: 1. Slotted screwdriver 2. Housing 3. Cover

4. Hole 5. Fan blade 6. Hook

Remaining

capacity

Blinking

50% to 100%

25% to 50%

10% to 25%

Less than

10%

Battery

abnormality

NOTICE:

Do not remove the fan blade from the

housing.

NOTICE:

Do not wash the fan unit with water.

Be sure to attach the cover after cleaning the fan blade. Place

the cover onto the housing as shown in the figure (note the

direction of the logo on the cover and the loop on the hous-

ing). Align the hooks with the holes and then snap it on.

► Fig.26: 1. Logo on the cover 2. Loop on the housing

Cleaning the jacket/vest

•

Detach the fan unit(s) and battery or battery holder

from the jacket/vest before washing.

•

Follow the instructions on the tag.

•

Cotton products may shrink when washed.

•

Do not wash the jacket/vest with other clothes.

Doing so may cause color fading or color transfer.

•

Use a laundry net when using a washing machine.

•

Do not use the fabric softener.

•

Use only neutral detergent.

•

After washing, take out the jacket/vest from wash-

ing machine at once.

•

Be sure to close the zip fastener before washing.

For the jacket with light reflector

•

The performance of light reflector parts may be

weakened by washing.

•

Machine wash in gentle cycle (The number of

times for washing is up to 5 times.)

•

The number of times for washing is not the only

the factor to decide the lifetime of the jacket.

•

The life of the jacket changes by how to use, how

to care and store state.

•

If the light reflector parts or clothes have been

deteriorated, replace to a new jacket.

NOTE: The features of the jacket/vest vary depend-

ing on the model.