Disposal And Recycling; Troubleshooting - Scheppach 5911218903 Originalbetriebsanleitung

• Change the oil at the end of every season. To do
so, remove the used engine oil from a warm engine
and refill with fresh oil.
• Remove the spark plug from the cylinder head. Fill
the cylinder with approx. 20 ml of oil from an oil can.
Slowly pull back the starter handle, which will bathe
the cylinder wall with oil. Screw the spark plug back
in.
• Clean the cooling fins of the cylinder and the hous-
ing.
• Be sure to clean the entire machine to protect the
paint.
• Store the machine in a well-ventilated place.
Preparing the mower for transportation (Fig. 22)
• Empty the petrol tank.
• Always let the engine run until it has used up the
remainder of petrol in the tank.
• Empty the engine oil from the warm engine.
• Remove the spark plug boot from the spark plug.
• Clean the cooling fins of the cylinder and the hous-
ing.
• Remove the start tension cable (17) from the hook.
Loosen the quick-release lever (5) and fold the up-
per push bar down. Make sure the cables are not
bent during this process.
• Wedge a few layers of corrugated cardboard be-
tween the upper and lower push bars and the en-
gine in order to prevent any chafing.

11. Disposal and recycling

Transport package disposal
The package protects the appliance against damage
during transport. Packing materials are usually cho-
sen depending on their environmental friendliness
and disposal method and can therefore be recycled.
Fault
Loud while running,
machine vibrates
heavily
Engine does not start
Engine runs unsteadily
Uneven mowing results
Unsatisfactory bagging
of the grass
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Possible cause
• Screws are loose
• Blade fasteners are loose
• Blade is unbalanced
• Brake lever not pressed
• Speed lever in wrong position
• Spark plug is defective
• Fuel tank is empty
• Contaminated fuel
• Cold environment
• Engine faulty
• Air filter is soiled
• Spark plug is soiled
• Blade is blunt
• Cutting height is too low
• Cutting height is too low
• Blade is worn
• Basket is clogged
Returning the package to material circulation saves
raw materials and reduces waste disposal costs.
Parts of packages (e.g. foils, styropor®) can be dan-
gerous to children. Risk of suffocation! Keep parts of
packages away from children and dispose them as
soon as possible.
The unit and its accessories are made of various
types of material, such as metal and plastic. Defec-
tive components must be disposed of as special
waste. Ask your dealer or your local council.

12. Troubleshooting

Troubleshooting
The table shows potential failures, their possible
cause and removal options. However, if you are un-
able to remove the problem, contact a professional
to assist you.
m CAUTION!
Always switch off the engine and pull the ignition ca-
ble before starting any inspection or adjustment work.
m CAUTION!
If, after making an adjustment or repair to the engine,
you let it run for a few minutes, remember that the ex-
haust and other parts will get hot. Thus, do not touch
parts that emanate heat, as these may burn you.
Important hint in case of sending the equipment
to a service station:
Due to security reasons please see to it that the
equipment is sent back free of oil and gas!
Remedy
• Check screws
• Check blade fasteners
• Replace blade
• Press brake lever
• Check setting
• Replace spark plug
• Refill with fuel
• Empty fuel tank and fill with clean fuel
• Push the primer button (if present)
• Contact authorised customer service
• Clean the air filter
• Clean the spark plug
• Sharpen the blade
• Set correct height
• Set correct height
• Replace the blade
• Empty the basket
30 | GB