"Delay Start" Button - Haier XIB 6B2S3FS Bedienungsanleitung

generally a warning sign that the salt container
needs filling.
In order to guarantee the correct functioning
of the salt indicator light, YOU MUST ALWAYS
FULLY REPLENISH THE SALT CONTAINER.

"DELAY START" BUTTON

Dishwasher start time can be set with this
button, delaying start from 1 to 23 hours.
Proceed as follows to set a delayed start:
Turn on the dishwasher by pressing the
•
"ON/OFF" button for about 3 sec.
Select the washing programme.
•
Press the " DELAY START" button ("0:30" will
•
appear on the display).
Press the button again to increase the delay
•
(on each press the delay is increased by
30 mins., up to a maximum of 23:30.
When the delay is set on a programme:
•
- after pressing
countdown time "00:00" appears on the
display with flashing " : "
- if you press any button (except for the
"ON/OFF", "PROGRAMME SELECTION"
buttons), the programme name is
displayed for a single scroll on the display
and then the delay time is displayed again.
- When the time has
programme name is displayed for a single
scroll on the display and the remaining
time will be displayed as "0:00h".
To start the
•
START/RESET button. The display will show
the time remaining to the end of the
programme. At the end of the countdown, the
programme will start automatically.
If the delayed start is not confirmed by
pressing the "START/RESET" button, after
approx. 10 sec. the delayed start will be
cancelled.
(Only for free-standing models)
The length of the selected cycle will be shown
on the display. At the end of the countdown,
the programme will automatically start and
the length of the selected cycle will be shown
on the display.
Proceed as follows to cancel a delayed start:
"START/RESET",
elapsed,
countdown, press
Hold the "START/RESET" button down for at
•
least 3 seconds. "00" will appear on the display
"RESET" and audible signals will sound.
The delayed
•
programme will be cancelled. Two dashes will
appear on the display.
At this point, to set off the dishwasher, a new
•
programme and any option buttons must be
selected, as indicated in the "PROGRAMME
SETTINGS" paragraph.
ACTIVATION/MUTED END-OF-PROGRAMME
SIGNAL
You can deactivate turning on and off of the
audio signal as follows (the default setting is
active):
The dishwasher must ALWAYS be off before
you start this procedure.
Turn on the dishwasher by holding the
•
the
"ON/OFF" button down for about 3 secs.
Hold down the "PROGRAMME SELECTION"
•
and "ON/OFF" buttons for about 5 secs.
The message "SETTINGS" will appear on the
•
display and the indicator lights of the
"OPTIONS" and "EXTRA DRY" buttons will be on.
Pressing the "PROGRAMME SELECTION"
•
button until the "BUZZER" parameter is
the
selected.
Parameter adjustment is performed by
•
pressing the "OPTIONS" and "EXTRA DRY"
buttons to change the value from YES to NO
and vice versa.
the
Switch off the dishwasher by pressing the
•
"ON/OFF" button for 3 secs to confirm the
new setting.
To turn the alarm on again, follow the same
procedure.
MEMO FUNCTION (Memorising the last
programme used)
The dishwasher must ALWAYS be off before
you start this procedure.
Turn on the dishwasher by holding the
•
"ON/OFF" button down for about 3 secs.
Hold down the "PROGRAMME SELECTION"
•
and "ON/OFF" buttons for about 5 secs.
The message "SETTINGS" will appear on the
•
display and the indicator lights of the
"OPTIONS" and "EXTRA DRY" buttons will be on.
EN 106
start and the selected