*** CV460 ***
2. IN 10 und
3. IN 11
Für diese beiden Digitaleingänge bestehen jeweils die folgenden
Einstellmöglichkeiten:
off
Digitaleingang ohne Funktion,
Q1:I>Y
Schaltelement Q1 hat Überstromauslösung *
Q2:I>Y
Schaltelement Q2 hat Überstromauslösung *
Bei gesetztem Eingang wird im Falle der Spannungsrückkehr auf der
bevorzugten Leitung eine zweite, den OP-Betrieb störende Unterbre-
chung der Spannung durch automatische Rückschaltung verhindert.
no2->1
Die Rückschaltung muss manuell zu einem geeigneten Zeitpunkt durch
Öffnen des Eingangs vorgenommen werden oder erfolgt automatisch
nach Ausfall der zweiten Leitung.
* nur für Umschalteinrichtungen mit Leistungsschaltern
4. 111-4,
5. 121-4,
6. 131-4 und
7. 141-4
Über diese vier Menüpunkte kann jeweils die Drahtbruchüberwa-
chung an den Schaltelementen wie folgt aktiviert werden:
off
keine Drahtbruchüberwachung,
Drahtbruchüberwachung eingeschaltet
*** RK4xx***
8. IN 10 und
9. IN 11
Für diese beiden Digitaleingänge bestehen jeweils die folgenden
Einstellmöglichkeiten:
off
Digitaleingang ohne Funktion
Q1:I>Y
Schaltelement Q1 hat Überstromauslösung *
Q2:I>Y
Schaltelement Q2 hat Überstromauslösung *
Bei gesetztem Eingang wird im Falle der Spannungsrückkehr auf der
bevorzugten Leitung eine zweite, den OP-Betrieb störende Unterbre-
chung der Spannung durch automatische Rückschaltung verhindert.
no2->1
Die Rückschaltung muss manuell zu einem geeigneten Zeitpunkt durch
Öffnen des Eingangs vorgenommen werden oder erfolgt automatisch
nach Ausfall der zweiten Leitung.
* nur für Umschalteinrichtungen mit Leistungsschaltern
Das bedeutet, das dem PRC487 alternativ über das RK4xx
eine Überstromauslösung der Schaltelemente oder
●
eine Aktivierung der Rückschaltsperre
●
gemeldet werden kann.
TBP204003deen / 04.2008
All manuals and user guides at all-guides.com
*** CV460 ***
2. IN 10 and
3. IN 11
The following settings are possible for these inputs:
off
Digital input without function
Q1:I>Y
Switching element Q1 with overcurrent release *
Q2:I>Y
Switching element Q2 with overcurrent release *
If the input is set and the voltage restored on the preferred supply, a
second power supply interruption in the operating theatre can be pre-
vented by automatic switchback.
no2->1
The reset must be carried out manually at an appropriate time by ope-
ning the input or is automatically carried out after failure of the second
supply.
* only valid for switchover modules with circuit breakers
4. 111-4,
5. 121-4,
6. 131-4 and
7. 141-4
Open circuit monitoring of the switching elements can be activa-
ted via these four menu items.
off
open circuit monitoring switched off
Open circuit monitoring switched on
*** RK4xx***
8. IN 10 and
9. IN 11
The following settings are possible for these digital inputs:
off
Digital input without function
Q1:I>Y
Switching element Q1 with overcurrent release *
Q2:I>Y
Switching element Q2 with overcurrent release *
If the input is set and the voltage restored on the preferred supply, a
second power supply interruption in the operating theatre can be pre-
no2->1
vented by automatic switchback. The reset must be carried out manu-
ally at an appropriate time by opening the input or is automatically
carried out after failure of the second supply.
* only valid for switchover modules with circuit breakers
That means that in addition
an overcurrent release of the switching elements or
●
an activation of the latching device
●
can be signalled to the PRC487 via the RK4xx.
PRC487
11