EINHELL 42.589.81 Originalbetriebsanleitung Seite 12

Anleitung_SMJ_500_E_SPK1:_
GB
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1. Fitting the additional handle (Fig. 2-3/Item 8)
The additional handle (8) enables you to achieve
better stability whilst using the hammer drill. Do not
use the tool without the additional handle.
The additional handle (8) is secured to the hammer
drill by a clamp. Turning the lock screw (a) clockwise
tightens this clamp. Turning it anti-clockwise will
release the clamp.
The supplied additional handle must first be fitted
in place. To do this, the clamp must be opened by
turning the locking screw (a) until it is wide
enough for the additional handle to be slid over
the chuck (1) and on to the hammer drill.
After you have mounted the additional handle (8),
swivel it to the most comfortable working position
for yourself.
Now re-tighten the locking screw (a) by turning it
in the opposite direction until the additional
handle is secure.
The additional handle (8) is suitable for both left-
handed and right-handed users.
5.2 Fitting and adjusting the depth stop
(Fig. 4/Item 2)
The depth stop (2) is held in place with the locking
screw (a) on the additional handle (8) by means of a
clamp.
Undo the locking screw (a) and fit the depth stop
(2).
Set the depth stop (2) to the same level as the
drill bit.
Pull the depth stop (2) back by the required
drilling depth.
Retighten the locking screw (a).
12
27.05.2009 7:41 Uhr Seite 12
Now drill the hole until the depth stop (2) touches
the workpiece.
5.3 Fitting the drill bit (Fig. 5)
Always pull the power plug before making
adjustments to the equipment.
Release the depth stop as described in 5.2 and
push it towards the additional handle. This
provides free access to the chuck (1).
This hammer drill is fitted with a keyless chuck
(1).
Open the chuck (1). The drill bit opening (1) must
be large enough to fit the drill bit into.
Select a suitable drill bit. Push the drill bit as far
as possible into the chuck opening.
Close the chuck (1). Check that the drill bit is
secure in the chuck (1).
Check at regular intervals that the drill bit or tool
is secure (pull the mains plug).
6. Operation
6.1 ON/OFF switch (Fig. 6/Item 5)
First fit a suitable drill bit into the tool (see 5.3).
Connect the mains plug to a suitable socket.
Position the drill in the position you wish to drill.
To switch on:
Press the ON/OFF switch (5)
Continuous operation:
Secure the ON/OFF switch (5) with the locking
button (4).
To switch off:
Press the ON/OFF switch (5) briefly.
6.2 Adjusting the speed (Fig. 6/Item 5)
You can infinitely vary the speed whilst using the
tool.
Select the speed by applying a greater or lesser
pressure to the ON/OFF switch (5).
Select the correct speed: The most suitable
speed depends on the workpiece, the type of use
and the drill bit used.
Low pressure on the ON/OFF switch (5): Lower
speed (suitable for: small screws and soft
materials)
Greater pressure on the ON/OFF switch (5):
Higher speed (suitable for large/long screws and
hard materials)