Deleting All Transmitters - Steute Rf Rx Sw868-2W-Rs232 Montage- Und Anschlussanleitung

RF Rx SW868/SW915/SW917/SW922-2W-RS232
//
Montage- und Anschlussanleitung / Funk-Empfänger
Mounting and wiring instructions / Wireless receiver
Instructions de montage et de câblage / Récepteur sans fil
Istruzioni di montaggio e collegamento / Ricevitore wireless
Instruções de montagem e instalação / Receptor sem fio
English
press push-button S1 for approx. 1 s. If you do not press the push-
button S1 again, the next operation mode is switched on after 5 s. The
operation modes »Linkage« and »Latching function« can be selected
in addition to the other operation modes.
Operation mode LED 1 LED MD
Standard flashes flashes
fast fast
Standard, flashes on
inverse output fast
Relay energised on flashes
fast
Relay energised, on on
inverse output
Linkage flashes on
(additionally slowly
selectable)
Latching on flashes
function slowly
(additionally
selectable)
Teaching in of transmitters
The output of the receiver can be switched by a maximum of 10 trans-
mitters per channel. To do this, teach in each transmitter once in the
receiver.
- Press push-button S1 approx. 1 s
- LED MD flashes slowly (2 Hz)
- Channel selection: press push-button S2
- Actuate transmitter to be taught in
- The LED of the corresponding channel is off for short time
- To leave teach-in mode: press push-button S1 approx. 1 s
- LED MD is on
Deleting one transmitter
- Press push-button S1 for 5 s until LED MD flashes fast
- Channel selection: press push-button S2
- Actuate transmitter to be deleted
- The LED of the corresponding channel is off for short time
- To leave delete mode: press push-button S1 approx. 1s
- LED MD lights green
Inverse teaching in of one transmitter
- Procedure like teach-in but transmitter must be actuated before pro-
cedure is started by pressing S1.
Function
Relay energised by actuation
Relay de-energised by actu-
ation, inverse output signal
Relay energised by providing
operating voltage
Relay energised by providing
operating voltage, inverse
output signal
Relay energised as soon
as one transmitter is actu-
ated, de-energises when all
taught-in transmitters are
not actuated
Latching function/
Impulse function
4 / 20

Deleting all transmitters

- Press push-button S1 for 5 s
- LED MD flashes fast (5 Hz)
- Channel selection: LED is on
- Release push-button S1
- Repress push-button S1 for 5 s until LED MD is off
- LED MD is on and LED 1 is off
- Operation mode was set back to standard
- Release push-button S1
- LED MD is on and LED 1 flashes fast
RF Rx SW868/915/922-2W-RS232
Selection of the baudrate
- Standard preset baudrate is 9,600 Bd
- Press push-buttons S1 and S2
- LEDs 1, 2 and MD are flashing
- Press push-button S2 for selection of baudrate
- LEDs B1 and B2 indicate the baudrate
- Press push-button S1 to select the desired baudrate
LED B1 LED B2
off off
on off
off on
on on
- To show the selected baudrate: Press push-button S1.
- To quit without changing the setting: Press push-buttons S1 and S2.
Telegrams
All steute Wireless telegrams are displayed at the serial interface.
Maintenance and cleaning
.steute recommends routine maintenance as follows:
1. Remove all dirt particles: Clean enclosure on the outside only.
Clean device in accordance with IP protection class. Clean with
a soft cloth and water or a mild detergent. Do not clean using com-
pressed air.
2. Replace damaged parts.
3. Test the function.
Disposal
- Observe national, local and legal regulations concerning disposal.
- Recycle each material separately.
Baudrate
9,600 Bd
19,200 Bd
38,400 Bd
57,600 Bd