Technical Data; English (Original Instructions) - DeWalt DCD85ME2GT Originalanweisung

DRILL
DCD85M
Congratulations!
You have chosen a D WALT tool. Years of experience, thorough
e
product development and innovation make D
most reliable partners for professional power tool users.

Technical Data

Voltage
Type
Battery type
No‑load speed
1st gear
2nd gear
Impact rate
1st gear
2nd gear
Max. torque (hard/soft)
Chuck capacity
Maximum drilling capacity
Wood
Metal
Masonry
Weight (without battery pack)
Noise values and/or vibration values (triax vector sum) according to
EN62841‑2‑1:
L (emission sound pressure level)
PA
L (sound power level)
WA
K (uncertainty for the given sound level)
Drilling into metal
Vibration emission value a
h,D
Uncertainty K =
Drilling into concrete
Vibration emission value a
h,ID
Uncertainty K =
The vibration and/or noise emission level given in this information
sheet has been measured in accordance with a standardised test
given in EN62841 and may be used to compare one tool with
another. It may be used for a preliminary assessment of exposure.

WARNING: The declared vibration and/or noise emission
level represents the main applications of the tool. However,
if the tool is used for different applications, with different
accessories or is poorly maintained, the vibration and/or
noise emission may differ. This may significantly increase the
exposure level over the total working period.
WALT one of the
e
DCD85M
V
DC
Li‑Ion
min 0–650
‑1
min 0–2000
‑1
min ‑1 0‑11050
min 0‑34000
‑1
Nm 90/27
mm 1.5–13.0
mm
mm
mm
kg
dB(A)
dB(A)
dB(A)
= m/s 2 < 2.5
m/s 2
= m/s 2
m/s 2
An estimation of the level of exposure to vibration and/or
noise should also take into account the times when the tool is
switched off or when it is running but not actually doing the
job. This may significantly reduce the exposure level over the
total working period.
Identify additional safety measures to protect the operator
from the effects of vibration and/or noise such as: maintain
the tool and the accessories, keep the hands warm (relevant
for vibration), organisation of work patterns.
18
EC‑Declaration of Conformity
1
Machinery Directive
Drill/Impact Drill
DCD85M
D WALT declares that these products described under Technical
e
Data are in compliance with:
EN 62841-1:2015 + AC:2015 + A11:2022; EN 62841-2-
1:2018+A11:2019.
These products also comply with Directive 2014/53/EU and
2011/65/EU. For more information, please contact D
55
the following address or refer to the back of the manual.
13
The undersigned is responsible for compilation of the technical
13
file and makes this declaration on behalf of D
1.34
Markus Rompel
90
Vice-President Engineering, PTE-Europe
101
D WALT, Richard-Klinger-Straße 11,
e
5
65510, Idstein, Germany
8.12.2022
DECLARATION OF CONFORMITY
1.5
THE SUPPLY OF MACHINERY (SAFETY)
11
1.5
D WALT declares that these products described under Technical
e
Data are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN 62841-1:2015 + AC:2015 + A11:2022; EN 62841-2-1:2018+A11:2019.
These products conform to the following UK Regulations:
REGULATIONS 2008
DRILL/IMPACT DRILL
DCD85M
EnGLIsH
WALT at
e
WALT.
e
27