Faults With Display; Accessories - Kärcher B 40 Bedienungsanleitung

Inhaltsverzeichnis

Verfügbare Sprachen

Display

ERR B

ERR T

LOW BAT

ERR TEMP

HandsOff

ERR REL

Failure

Correction

Appliance cannot be

Turn the program selection switch to the desired programme.

started

Operate the safety switch.

Check battery; charge it if required.

Make sure that all battery terminals are connected.

Insufficient water quan-

Check fresh water level, refill tank if necessary.

tity

Increase the water volume on the regulating knob for water volume.

Unscrew the lock of the fresh water reservoir. Remove and clean the fresh water filter. Insert the filter and screw

in the lock.

Remove the water distribution strip from the cleaning head and clean water canal (only R cleaning head).

Check hoses for blockages; clean if required.

Insufficient vacuum per-

Clean the seals between waste water tank and cover and check for tightness, replace if required.

formance

Wastewater reservoir is full; shut off the appliance and empty the wastewater reservoir

Clean the fluff filter.

B 60 W Bp only:

Check protective turbine strainer for soiling, clean if necessary.

Clean the vacuum lips on the vacuum bar, replace if required

Check suction hose for blockages; clean if required.

Check the suction hose for tightness; replace if required.

Check if the cover on the dirt water discharge hose is closed

Check the setting of the vacuum bar.

Insufficient cleaning re-

Check the brushes for wear, replace if required.

sult

Brushes do not turn

Check if foreign matters block the brushes; remove foreign matter if required.

If over-current switch in the electronics system has been triggered, turn programme selection switch to "OFF".

Afterwards, set it back to the desired programme.

Vibrations during clean-

You might need to use softer brushes.

ing

Brushes deformed, because the appliance was stored with the cleaning head lowered. Replace brushes.

In case of faults that cannot be remedied using the table below please contact the customer service.

Description

Brush roller, red (medium, stand-

ard)

Brush roller, white (soft)

Brush roller, orange (high/ low)

Brush roller, green (grit)

Brush roller, grey (1 mm grit)

Pad roller shaft

Roller pad, white (very soft)

Roller pad, yellow (soft)

Roller pad, red (medium)

Roller pad, green (hard)

Correction

Check if foreign matters block the brushes; remove foreign matter if required.

Call customer service.

Charging battery

Allow device to cool down.

Reduce brush contact pressure, if necessary.

Release the safety switch and wait until the operating hours or the battery status are shown on the display.

Then operate the safety switch again.

Set the programme selector switch to "OFF", release the safety switch, wait for 3 seconds, restart.

If the event recurs, call Customer Service.

Faults without display on the console

BR devices (roller brushes accessories)

Part no.:

Working

width

450 mm

550 mm

4.762-392.0 4.762-393.0 Also for regular cleaning of heavily dirtied floors.

4.762-405.0 4.762-409.0 For polishing and cleaning sensitive floors.

4.762-406.0 4.762-410.0 For scrubbing structured floors (safety tiles, etc.).

4.762-407.0 4.762-411.0 For thoroughly cleaning heavily dirtied floors and for

4.762-408.0 4.762-412.0

4.762-413.0 4.762-415.0 For intake of roller pads.

6.367-108.0 6.369-735.0 For cleaning and polishing sensitive floorings.

6.367-105.0 6.369-732.0 For polishing floors.

6.367-107.0 6.369-734.0 For cleaning slightly dirtied floors.

6.367-106.0 6.369-733.0 For cleaning normal to heavily dirtied floors.