Gaggenau 400 Serie Montageanleitung Seite 14

You can install the appliance in the following
temperature-resistant and waterproof worktops:
Stone worktops
¡
Plastic worktops, e.g. Corian®
¡
Solid wood worktops
¡
Coordinate with the worktop manufacturer when us-
ing other materials.
Installation in compressed-wood worktops is not pos-
sible.
Have all cut-out work on the worktops carried out in
a specialist workshop in compliance with the installa-
tion diagram. The cut-out must be neat and precise
since the cut edge is visible on the surface.
Clean and degrease the cut-out edges with a suit-
able cleaning agent. When doing so, observe the us-
age instructions from the silicone manufacturer.
Observing the position of the gas
connection
Observe the position of the gas connection when
▶
installing the appliance.
→ Fig.
5
Installing the appliance flush with the
frameless induction hobs
For flush installation in combination with frameless
1.
induction hobs, cut out the support edge with
6.5 mm.
Make the unit cut-out in the worktop for one or
2.
more Vario appliances in accordance with the in-
stallation drawing.
Observe the installation instructions for the
‒
VA420004 connection strip.
→ Fig.
6
Preparing the appliance
Screw the corresponding connection elbow with
▶
the seal onto the appliance.
→ Fig.
7
Preparing the unit
Requirement: The fitted units are heat-resistant up to
90 °C.
Ensure that the stability of the fitted unit is guaran-
1.
teed after the cut-outs have been made.
Make the unit cut-out in the worktop for one or
2.
more Vario series appliances in accordance with
the installation drawing.
When installing several Vario series appliances
‒
next to each other, allow for the space required
for the connection strip.
Observe the installation instructions for the
‒
VA420004/VA420010 connection strip.
When installing several Vario series appliances
‒
in single cut-outs, observe the minimum dis-
tance of 50 mm between the appliances.
When installing the VA440010 appliance cover,
‒
take the additional space required into consid-
eration.
→ Fig. , → Fig. , → Fig.
8 9
The VA420004/VA420010 connection strip is
available as a special accessory.
For flush installation, mark the unit cut-out in ac-
3.
cordance with the installation diagram.
→ Fig. , → Fig.
11 12
The appliance cover VA440010 can be ordered
separately as a special accessory.
Observe the worktop thickness and the distance
4.
between the worktop and the bottom edge of the
appliance.
→ Fig.
13
14
10
For flush installation, observe the worktop thick-
5.
ness and the distance between the worktop and
the bottom edge of the appliance.
→ Fig.
14
Drill four holes with a diameter of 6 mm.
6.
→ Fig.
15
Ensure that the angle of the cut surface to the
7.
worktop is 90°.
→ Fig.
15
Ensure that the cut-out edges at the sides are at
8.
least 20 mm thick and flat to ensure that the re-
taining springs sit correctly on the appliance.
For multi-layer worktops, affix appropriate strips to
9.
the side in the unit cut-out, if required.
After making the cut-outs, remove any shavings.
10.
Seal the cut surfaces so that they are heat-resist-
11.
ant and waterproof.
→ Fig.
15
Observe the minimum clearance of 10 mm
12.
between the bottom of the appliance and unit
parts.
Use suitable substructures to ensure the load-
13.
bearing capacity and stability of the unit, particu-
larly in the case of thin worktops.
Take the appliance weight, including additional
‒
load, into consideration.
Use heat-resistant and moisture-resistant rein-
‒
forcement material.
Making the cut-out for the control knob
Drill the hole for the control knob according to the
1.
enclosed instructions.
If the panel is more than 23 mm thick, cut out the
2.
rear of the front panel for the retaining plate.
Note the position of the control knob.
3.
→ Fig.
16
After making the cut-outs, remove any shavings.
4.
Seal the cut surfaces so that they are heat-resist-
5.
ant and waterproof.
Installing the control knob
Follow the installation instructions provided for the
1.
control knobs.
Hold the retaining plate in place against the rear
2.
of the control panel.
Use 2 screws to secure the retaining plate against
3.
rotation.
In the case of stone worktops, adhere the re-
‒
taining plate using heat-resistant, two-compon-
ent adhesive.
→ Fig.
17
Remove the protective film from the rear of the il-
4.
luminated ring.
→ Fig.
18
Push the control knob into the hole.
5.
Always position the side marking on the control
‒
knob on the left.
Ensure that the retaining lug on the retaining plate
6.
is located on the upper side and the control knob
is in the zero setting.
→ Fig.
19
On the rear of the control knob, tighten the retain-
7.
ing nut using the installation tool provided.
→ Fig.
20
Align the control knob precisely in the zero setting.
8.