Gaggenau 400 Serie Montageanleitung Seite 13

Ensure that there is a door leading outdoors or a
▶
window that can be opened.
For up to 11 kW total power: Ensure that the min-
▶
imum volume of the installation area is 20 m³.
For up to 18 kW total power: Ensure that the min-
▶
imum volume of the installation area is 2 m³ per
kW of the total power of the gas hob and that
there is an extractor hood that leads outside with
a minimum extraction rate of 15 m³/h per kW total
power of the gas hob.
Escaping gas may cause an explosion or poison-
ings.
This appliance is not connected to a waste gas
▶
main.
Install and connect this appliance in accordance
▶
with the applicable installation conditions.
Comply with all ventilation regulations.
▶
Do not connect this appliance to a waste gas
▶
main.
WARNING ‒ Risk of suffocation!
Children may put packaging material over their
heads or wrap themselves up in it and suffocate.
Keep packaging material away from children.
▶
Do not let children play with packaging material.
▶
Information about the installation room
For safe operation, observe the following information
regarding the installation area.
This appliance complies with appliance class 3 for
¡
installation in a kitchen unit.
Install the appliance in a kitchen unit in accord-
¡
ance with the installation diagram.
Ensure that the wall behind the appliance is made
¡
of non-combustible material.
Information about the gas connection
To safely connect the appliance, observe this inform-
ation.
For the installation, observe the currently applic-
¡
able building regulations and the regulations of
the local gas suppliers.
Ensure that the information on the rating plate re-
¡
garding the gas type and gas pressure complies
with the local connection conditions.
The gas connection must be arranged so that the
¡
shut-off valve is accessible.
The appliance comes with two connection elbows
(appliance-side G½'').
Select the right version according to the country:
ISO 228 G 1/2 cylindrical
¡
EN 10226 R 1/2 conical
¡
Use one of the supplied connection elbows and the
corresponding seal to connect the appliance to a
fixed power cable or a gas safety hose.
The gas safety hose should have a length of at least
1 m up to a maximum of 3 m.
Observe the information about the gas safety hose:
If the gas safety hose is made of metal, the per-
¡
missible ambient temperature is 115 °C. If the
gas safety hose is not made of metal or is only
partially made of metal, the ambient temperature
must not exceed 90 °C.
The gas safety hose must not come into contact
¡
with moving parts of the fitted unit (e.g. drawers)
or be routed in areas where it could become
trapped or damaged.
The gas safety hose must not come into contact
¡
with a hob, oven, dishwasher, refrigerator, wash-
ing machine, hot water pipes, radiator or any other
appliance installed next to or below the gas hob.
The gas safety hose must not be subject to rub-
¡
bing, vibrations, kinking or any other kind of de-
formation. It should be checked along its entire
length with the hob in the installation position.
Information about the electrical
connection
In order to safely connect the appliance electrically,
observe this information.
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appli-
ance from the electricity supply. The appliance must
only be connected to a protective contact socket
that has been correctly installed.
The mains plug of the mains power cable must be
▶
easily accessible after installation of the appliance.
If this is not possible, an all-pole isolating switch
▶
must be integrated into the permanent electrical
installation according to the conditions of over-
voltage category III and according to the installa-
tion regulations.
The permanent electrical installation must only be
▶
wired by a professional electrician. We recom-
mend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
Sharp-edged or hot components inside the appli-
ance may damage the connection cable.
Do not kink or trap the connection cable.
▶
Do not route the connection cable along hot sur-
▶
faces.
Incorrect repairs are dangerous.
Repairs to the appliance should only be carried
▶
out by trained specialist staff.
Only use genuine spare parts when repairing the
▶
appliance.
If the power cord of this appliance is damaged, it
▶
must be replaced by the manufacturer, the manu-
facturer's Customer Service or a similarly qualified
person in order to prevent any risk.
Ensure that the information on the rating plate re-
¡
garding the output and voltage complies with the
local connection conditions.
The appliance corresponds to protection class 1.
¡
You should therefore only use the appliance with
a protective earth connection.
Do not connect the appliance to the power supply
¡
during installation.
Ensure that the protection against contact is guar-
¡
anteed during installation.
Only a qualified electrician may connect appli-
¡
ances without a plug. They are subject to the re-
quirements of the local electricity provider.
Do not use the appliance with an external timer or
¡
a remote control.
The appliance must only be connected using the
¡
power cable provided.
Information on fitted units
Observe the cut-out dimensions and the installation
instructions when installing in a worktop.
The fitted units must be heat-resistant to at least
90 °C.
Ensure that the stability of the fitted unit is guaran-
teed after the cut-outs have been made.
To improve flame stability, install an intermediate
floor underneath the appliance in the installation cab-
inet.
Information about flush installation
With the flush installation, the appliance and worktop
are on one level. There is no unattractive stepping
between the appliance and the worktop.
13