Functional Group Record; Live Surveillance, Audio And Video Recordings; Functional Group Video; Replaying And Managing Recordings - Monacor DMR-250SET Bedienungsanleitung

7 Functional Group RECORD

GB
Live surveillance
Video and audio recordings
1) If the basic menu (fig. 2) fails to appear on the dis-
play, press the button STOP/ ESC (5) [repeatedly].
2) Select RECORD with the button
press the button
image presently recorded by the camera (live sur-
veillance). "Preview" will be inserted on the display
for information.
Note: To stop the live surveillance, press the button
STOP/ ESC (5).
3) To start recording, press the orange button REC /
PAUSE (6) or the button
(22).
4) To pause and continue the recording at any time,
press the button REC / PAUSE or
5) To stop a recording, keep the button STOP/ ESC (5)
or the button
the display shows an hour glass and "Please
Wait...".
The recorder will store the recording as a file and
then switch to the functional group VIDEO. The list
of video recordings will appear. The last recording is
selected. Press the button
To stop the replay, press the button STOP/ ESC;
the list of video recordings will reappear. To return
to the basic menu, press the button STOP/ ESC
twice.
Notes
1. It is not possible to stop a recording again within the first
5 seconds.
2. To start recording without a preview from the basic menu
or from the functional groups VIDEO and SETTING,
press the button REC/ PAUSE.
3. The maximum size of a recording is 4 GB. When the
recording has reached this size, it will be stored as a file.
The recording will then be continued with a new file.
4. Audio recording is not possible when the frame rate has
been set to 5 fps (SETTING → Record Setup → Frame
Rate).
5. If an error message of a crossed-out camera icon and the
text "No Signal" appears, check the following items:
– Has the camera been correctly connected? If the cam-
era was connected when the recorder had already
been switched on, switch off the recorder, then switch it
on again.
– Via the menu item "Video Format", PAL must be set
(SETTING → Display Setup).
Further possibilities
1. Endless recording: The file created will be continu-
ously overwritten by more recent recordings.
SETTING → Record Setup → Endless Recording
2. Time-controlled recording (even with the recorder
switched off): SETTING → Timer Record Setup
With a correct setting, the clock icon will appear (c);
it will start flashing one minute before the recording
starts.
3. To be able to use the internal memory when an
SDHC card has been inserted, set the menu item
16
or
(13). The display will show the
on the remote control
.
on the remote control pressed until
to replay it.
"Memory Change" to YES
(SETTING → Memory Setup)
4. When the display shows the camera preview ("Pre-
view"), a press of the button MENU (7) will activate a
submenu. This submenu allows you to set the record-
ing time (Record Time) and to change the micro-
(12) and
phone sensitivity (Mic Sensitivity: High / Middle / Low).
5. To activate and deactivate a submenu while record-
ing, press the button MENU (7). This submenu
allows you to show the recording time adjusted
(Record Time) and to change the microphone sen-
sitivity (Mic Sensitivity).
6. To save storage space, the submenu "Record
Setup" of the function SETTING allows you:
– to make video recording only (Input Source)
– to reduce the video quality
– to reduce the resolution
– to reduce the frame rate
– to pause recording when no motion is detected in
the image (Motion Detect)
– to set a maximum recording time

8 Functional Group VIDEO

Replaying and managing recordings

1) If the basic menu (fig. 2) fails to appear on the dis-
play, press the button STOP/ ESC (5) [repeatedly].
2) To access the recordings made on a memory card
inserted, the SD card icon (d) must be displayed in
the basic menu. If it is not displayed, keep the but-
ton MENU (7) pressed until the icon appears. To
switch back to the internal memory, proceed in the
same way.
3) Select VIDEO with the button
press the button
list of video recordings. The file names created by
the recorder are coded as follows:

8.1 Replaying recordings

1) Select the recording to be replayed from the file list
with the button
with the button
2) If the sound has also been recorded, adjust the vol-
ume with the buttons VOL - and + (11).
Note: If there is no sound, set the menu item "Speaker
Control" to ON.
(SETTING → System Setup → Speaker Control)
3) To pause and continue the replay at any time, press
the button
oder
(13). The display will show the
or (12) and start the replay
(13).
.
(12) and