Specifications - Makita BTD120 Betriebsanleitung

ENGLISH
1 Red part
2 Button
3 Battery cartridge
4 Terminal cover
5 Charging lights
6 Battery charger
7 Bit
8 Sleeve

SPECIFICATIONS

Model
Capacities
Machine screw ................................. 4 mm – 8 mm
Standard bolt .................................. 5 mm – 12 mm
High tensile bolt ............................. 5 mm – 10 mm
–1
No load speed (min ) ............................... 0 – 2,300
Impacts per minute .................................... 0 – 3,000
Overall length ............................................... 168 mm
Net weight ....................................................... 1.5 kg
Rated voltage ............................................ D.C. 12 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
4
Explanation of general view
9 Switch trigger
10 Reversing switch lever
11 A side
12 B side
13 Clockwise
14 Counterclockwise
15 N . m (kgf . cm)
9. Do not operate charger if it has received a
BTD120
10. Do not disassemble charger or battery car-
11. To reduce risk of electric shock, unplug
12. The battery charger is not intended for use by
13. Young children should be supervised to
14. If operating time has become excessively
15. If electrolyte gets into your eyes, rinse them
ENC002-3
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
2. Do not attempt to use a step-up transformer,
3. Do not allow anything to cover or clog the
4. Do not short the battery cartridge:
16 Fastening torque
17 Proper fastening torque for
18 Seconds
19 Fastening time
20 Limit mark
21 Brush holder cap
22 Screwdriver
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
young children or infirm persons without
supervision.
ensure that they do not play with the battery
charger.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
an engine generator or DC power receptacle.
charger vents.
(1) Do not touch the terminals with any con-
ductive material.
(2) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.