Specifications; Additional Safety Rules For Tool - Makita BTD150 Betriebsanleitung

ENGLISH
1 Red part
2 Button
3 Battery cartridge
4 Terminal cover
5 Charging lights
6 Battery charger
7 Bit

SPECIFICATIONS

Model
Capacities
Machine screw ............................................ 4 mm – 10 mm
Self drilling screw ......................................... 4 mm – 6 mm
–1
No load speed (min ) ............................................ 0 – 2,300
Impacts per minute ................................................. 0 – 3,000
Overall length ............................................................ 190 mm
Net weight .................................................................... 1.8 kg
Rated voltage ...................................................... D.C. 14.4 V
• Due to our continuing program of research and develop-
ment, the specifications herein are subject to change with-
out notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual con-
tains important safety and operating instructions for
battery charger.
2. Before using battery charger, read all instructions
and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. CAUTION — To reduce risk of injury, charge only
MAKITA type rechargeable batteries. Other types of
batteries may burst causing personal injury and dam-
age.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord,
pull by plug rather than cord when disconnecting
charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
8. Do not operate charger with damaged cord or
plug — replace them immediately.
9. Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way; take
it to a qualified serviceman.
10. Do not disassemble charger or battery cartridge; take
it to a qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or fire.
11. To reduce risk of electric shock, unplug charger from
outlet before attempting any maintenance or clean-
ing. Turning off controls will not reduce this risk.
12. The battery charger is not intended for use by young
children or infirm persons without supervision.
13. Young children should be supervised to ensure that
they do not play with the battery charger.
Explanation of general view
8 Sleeve
9 Switch trigger
10 Reversing switch lever
11 A side
12 B side
13 Clockwise
14 Counterclockwise
14. If operating time has become excessively shorter,
BTD150
15. If electrolyte gets into your eyes, rinse them out with
ADDITIONAL SAFETY RULES FOR CHARGER
& BATTERY CARTRIDGE
1. Do not charge battery cartridge when temperature is
2. Do not attempt to use a step-up transformer, an
3. Do not allow anything to cover or clog the charger
4. Do not short the battery cartridge:
ENC002-3
5. Do not store the tool and battery cartridge in loca-
6. Do not incinerate the battery cartridge even if it is
7. Be careful not to drop, shake or strike battery.
8. Do not charge inside a box or container of any kind.
ADDITIONAL SAFETY RULES
FOR TOOL
1. Be aware that this tool is always in an operating
2. Hold tool by insulated gripping surfaces when per-
3. Always be sure you have a firm footing.
4. Hold the tool firmly.
5. Wear ear protectors.
SAVE THESE INSTRUCTIONS.
15 Wood screw size
16 Seconds
17 Fastening time
18 Limit mark
19 Brush holder cap
20 Screwdriver
stop operating immediately. It may result in a risk of
overheating, possible burns and even an explosion.
clear water and seek medical attention right away. It
may result in loss of your eyesight.
BELOW 10°C (50°F) or ABOVE 40°C (104°F).
engine generator or DC power receptacle.
vents.
(1) Do not touch the terminals with any conductive
material.
(2) Avoid storing battery cartridge in a container with
other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, over-
heating, possible burns and even a breakdown.
tions where the temperature may reach or exceed
50°C (122°F).
severely damaged or is completely worn out. The
battery cartridge can explode in a fire.
The battery must be placed in a well ventilated area
during charging.
condition, because it does not have to be plugged
into an electrical outlet.
forming an operation where the cutting tool may
contact hidden wiring. Contact with a ''live'' wire will
also make exposed metal parts of the tool ''live'' and
shock the operator.
Be sure no one is below when using the tool in high
locations.
ENB024-1
3