Werbung
ENGLISH
1
Lock button
2
Switch trigger
3
Hook
4
Casing
5
Thumb screws
6
Bit
7
Dust cover
8
Plain bearing
SPECIFICATIONS
Model
Screw strip ................................ 4 mm x 25 mm – 40 mm
–1
No load speed (min
) ............................................ 6,000
Overall length ..................................................... 364 mm
Net weight ............................................................. 2.1 kg
Safety class .............................................................
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained
from
repeated
adherence to screwdriver safety rules. If you use
this tool unsafely or incorrectly, you can suffer
serious personal injury.
1.
Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3.
Hold the tool firmly.
4.
Keep hands away from rotating parts.
5.
Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
6
Explanation of general view
9
Lever
10 Stopper base
11 Plate
12 Adjusting knob
13 Lock lever
14 Magazine cap
15 Screw strip
16 Magazine
6837
/II
GEB017-1
use)
replace
strict
17 Slotted passage
18 Portion A
19 Screw-driving position
20 Reverse button
21 Extension handle
22 Limit mark
23 Screwdriver
24 Brush holder cap
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the trigger. Release the trig-
ger to stop.
For continuous operation, pull the trigger and then push
in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
Hook (Fig. 2)
The hook is convenient for hooking the tool to your belt. It
can be installed on either side of the tool. To remove it,
pull it out in the direction of the arrow while raising. To
install the hook, push it down until it "clicks" into place on
the tool.
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing or removing bit
Loosen the thumb screws which secure the casing. Pull
out the casing in the direction of the arrow. (Fig. 3)
Press the dust cover toward the plain bearing and pull
out the bit. If the dust cover cannot be moved as far as
the plain bearing, try it again after turning the bit slightly.
To install the bit, insert it into the socket while turning it
slightly. After installing, always make sure that the bit is
securely held in place by trying to pull it out. (Fig. 4)
Werbung
