Control Parameters; Parameter List; Gpio Connector Overview - Tascam SB-16D Bedienungsanleitung

Control parameters

Parameter list

This unit has the following parameters.
They can all be controlled using a dedicated app and from a TASCAM Sonicview Series unit.
Function
Head Amp GAIN adjustment
PAD ON/OFF
PHANTOM ON/OFF
Sampling rate setting
Device name setting
Channel label settings
Switching the reference level
Indicator brightness adjustment
Identify
Network settings
(Dante Primary/Dante
Secondary/SB-16D unit)
Password setting
GPIO setting
Preset setting

GPIO connector overview

The GPIO connector on the back is a parallel control connector
for conducting external control of this unit.
In addition to external control of the SB-16D, GPIO connector
functions can also be set for use as extensions of the TASCAM
digital mixer GPIO connector. These can be set using the
TASCAM IO CONTROL app or a TASCAM digital mixer that
supports connection with this unit.
To use this unit by itself, see "GPIO settings" in the TASCAM IO
CONTROL reference manual.
When connected to a TASCAM Sonicview Series unit, this can be
done on the GPIO-IN and GPIO-OUT pages of the USER DEFINED
CONTROLS screen. For details, see "GPIO-IN page" and "GPIO-
OUT page" in "4 – Mixer configuration and other settings" of the
Reference Manual for the Sonicview Series unit.
The pin assignments are as follows.
Pin No. Function
1 GND
2 GPIO IN 2
3 GPIO IN 4
4 GPIO IN 6
5 GPIO IN 8
6 NC
7 NC
8 NC
9 GPIO OUT 2
10 GPIO OUT 4
16
TASCAM SB-16D
Digital reference level settings
Analog reference level settings
Static/Auto (DHCP)
IP Address
Subnet Mask
IN/OUT
-
IN
IN
IN
IN
-
-
-
OUT
OUT
Notes
When Analog Reference Level = +6 dBu
When PAD OFF: +12 dB – +66 dB
When PAD ON: -8 dB – +46 dB
When Analog Reference Level = +4 dBu
When PAD OFF: +3 dB – +57 dB
When PAD ON: -17 dB – +37 dB
When Analog Reference Level = 0 dBu
When PAD OFF: +8 dB – +62 dB
When PAD ON: -12 dB – +42 dB
-20 dB when on
+48V when on
96 kHz (default)/48 kHz
Set/change the device name as desired
Set/change channel names as desired
-9 dBFs/-14 dBFs/-16 dBFs/-18 dBFs/-20dBFs (default)
+6dBu (when -9dBFs)/+4dBu (default)/+0dBu
Setting range: 0–3 (default) (in 1 ms steps)
Makes all SIG and STATUS indicators on the unit blink
Automatic acquisition/manual setting for IP address
IP address can be set/changed when "Static"
Subnet Mask can be set/changed when "Static"
Set/change password as desired (no password by default)
Set/change function assigned to GPIO connector
Set presets
Pin No. Function
11 GPIO OUT 6
12 GPIO OUT 8
13 NC
14 GPIO IN 1
15 GPIO IN 3
16 GPIO IN 5
17 GPIO IN 7
18 NC
19 NC
20 GND
21 GPIO OUT 1
22 GPIO OUT 3
23 GPIO OUT 5
24 GPIO OUT 7
25 +5V
IN: For command input
i Internal circuit with +5V pull-up
i Operates with low signal input of 50 msec or longer
OUT: For command and tally output
i Internal circuit is open collector (10Ω output impedance)
i 20V dielectric strength, 35mA maximum current
+5V: 50mA maximum supplied current
IN/OUT
OUT
OUT
-
IN
IN
IN
IN
-
-
-
OUT
OUT
OUT
OUT
-